Ryobi Trimmer Hoses and Tubes

This is a genuine OEM approved replacement part, it is specially designed for use with Craftsman gas powered lawn and garden equipment. By pressing on the purge bulb, it will force fuel into the fuel line from the fuel tank into the carburetor. Once the carburetor is full of fuel, the excess fuel will be purged back into the tank in the fuel return line. Over time the material may begin to deterio...

The 791-682039 Fuel Filter and Line, filters the fuel in the tank as it is forced into the carburetor up by means of the primer bulb. To install. Remove retainer ring from fuel line. Insert fuel line thru gas cap opening. Thread fuel line thru hole in bottom of the fuel tank. Pull fuel line thru to firmly seat against inside tank wall. Put retainer ring on fuel line,hold line and press ring firml...

This fuel line is an original part from Craftsman for trimmers, blowers, edgers and cultivators. This part is supplying gas, starting with the tank to the carburetor. You will need a screw driver, pliers, a hose pulling wire and cutters to replace this part. This fuel line is made of rubber and sold individually.

The purpose of the 791-182352 Fuel Return Tube is to return the excess fuel back into the fuel tank, after the primer bulb has been pressed and has primed the carburetor to start. Over time the Fuel Return Line will become brittle and crack and will need to be replaced.

This breather hose is supplied directly from the original equipment manufacturer. Used in many outdoor trimmer devices, the breather hose is fitted onto the check valve. This item is available as an individual replacement. A set of pliers might be necessary during the installation of this part.

The breather hose attaches to the check valve. This item is available as an individual replacement. This is an authentic OEM part for use in trimmers and edgers made by Ryobi. A set of pliers might be necessary during the installation of this part. It is made of rubber and will require replacing if it becomes broken or leaks.

The breather hose attaches to the check valve. This item is sold individually and is made out of rubber. This is an OEM part sourced directly from the manufacturer and used in Ryobi blowers, trimmers, and edgers. A set of pliers might be necessary during the installation of this part. It will need to be replaced if it breaks.

This is a genuine OEM sourced part that is specially designed for use with Ryobi lawn and garden equipment. This breather acts as a valve for the fuel tank, it allows for the air to enter the fuel tank but it won't allow fuel or fuel emissions to leave the tank. Unfortunately, over time the material may wear out and begin to crack eventually requiring a replacement. Keep in mind this high-quality ...

The tube is a genuine original manufacturer part used in lawn and garden equipment. The durable rubber tube is the return fuel line that sends fuel from the carburetor to the fuel tank. Over time the fuel lines can degrade, and this replacement part is a great solution. The part is sold as one rubber tube.

This is a genuine OEM replacement part, it is sold individually. The purpose of this part is to connect the fuel line extending from the fuel tank to the fuel line that connects to the carburetor. Over time the fuel lines will become brittle and oversized. They will have to be replaced. This would be a good time to replace the Fuel Fitting also.

This is an original replacement part manufactured for use with outdoor power equipment. The breather hose is commonly used to allow combustion gasses to escape the crankcase. This breather hose is available as an individual replacement part, please see model diagram for associative parts.

It is a genuine OEM item that is designed for use with a variety of lawn and garden equipment. The breather tube is used to guide the direction of excess gasses and fluid that escape the engine from a higher level of internal pressure. If the part is cracked, damaged or missing, this will provide an identical replacement for the original component that was installed on a new unit. Note, this high-...

This replacement fuel line assembly includes the in-tank fuel filter that is specially manufactured for use with Ryobi string trimmers. It is purpose is to ensure the fuel that is supplied into the carburetor is free of any dirt and other debris that may be in the tank. Over time it may get clogged restricting the fuel flow and eventually requiring a replacement. It is made from durable plastic ma...