Craftsman Trimmer Springs and Shock Absorbers

Genuine Black and Decker replacement part, this item is sold individually. The purpose of the 90566944 Spring is to hold the spool in place on the Trimmer shown below. It is placed between the spool and the spool cover. The cover snaps into the spool housing by means of the two tabs on both sides of the cover.

Genuine OEM replacement part, this item is sold individually. This spring is used on all of the trimmers listed below. It is installed between the inner reel and the outer spool assembly. Its purpose is to keep pressure on the Bump Head Knob Assembly.

Genuine Black and Decker replacement part, it is sold individually. The purpose of the 682235-00 spring is to keep tension between the spool and the spool housing. Overtime the spring will lose its tension and will have to be replaced.

This is an OEM part guaranteed to fit Milwaukee power tools. This trigger spring is attached to main trigger. Please note that only trigger spring is included. When disassembling this area, be sure to slowly separate parts in order to prevent springs from being lost when released too quickly. Though they appear similar, a lockout spring is a different part used with the throttle lockout (not prese...

Genuine Black and Decker replacement part, this item is sold individually. The purpose of this spring is to hold the spool of the trimmer in the spool housing. Over time the spring will loose its tension and will have to be replaced.

This is a genuine Craftsman Part for use with Line Trimmers. The idler arm return spring returns the idler arm into position, releasing tension on the belt. The most common reason for replacing the spring is if the blades won't turn. This part is sold individually. The tool that you will need to replace the Idler return spring is Pliers.

This is a genuine Black and Decker replacement part that has been sourced from the original manufacturer to be used with trimmers. The metal spring is part of the cutting head assembly. The spring is used to provide compression between the cap and the spool. The spring is priced as a single item.

This is a genuine manufacturer sourced replacement part that is specially produced for use with Poulan and Weed Eater trimmers. It is an identical replacement for a missing or a faulty spring that was installed on a new unit. This spring helps to apply tension on the trimmer head, please make sure to refer to the appropriate diagram of your model for the correct location and application of this ha...

This is a genuine manufacturer approved replacement mulching door torsion spring designed for use with handheld trimmers/edgers. This spring helps the throttle trigger to retract. It is made out of metal and it is sold individually. Replacing this item you would need a screwdriver and pliers.

This is an original replacement part sourced directly from the manufacturer. The spring is found in Craftsman trimmers. This part is made of metal, and is used in the starter assembly to provide torsion to the starter hub. You may require an Allen wrench or screwdriver when replacing this item. The spring is sold as an individual replacement part.

This spring-driver is sourced directly from the original equipment manufacturer for Husqvarna and Jonsered handheld trimmers. It is an important part which applies tension on the driver-pulley, allowing it to retract. Over time it may wear out or get damaged eventually requiring a replacement to ensure the starter mechanism functions properly. To ensure the correct installation of this hardware, c...

This is an authentic replacement part that has been sourced from the original manufacturer to be used with trimmers from Ryobi, MTD, Troy-Bilt, Yard-Man, and Bolens. The recoil spring is part of the starter assembly and is used to wind the rope back around the pulley after it has been pulled. This spring is priced as a single item.

It is an authentic manufacturer-supplied part that is specially made for use with lawn and garden equipment. This is an identical replacement for a missing or a faulty clutch spring that was installed on a new unit. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality clutch spring is made of d...

This is a genuine manufacturer-sourced component which is specially produced for use with Troy-Bilt, Yard Man and MTD handheld string trimmers. It is an identical replacement for a missing or a faulty spring that was installed on a new unit. The purpose of this hardware is to apply tension on the throttle trigger. Please make sure to refer to the appropriate diagrams of your model for the correct ...

The spring fits between the outer spool & eyelet assembly and the inner reel. It is a genuine item that is supplied by the original equipment manufacturer for use with trimmers made by Ryobi, Troy-Bilt, Bolens, Yard Man, MTD, and Cub Cadet. A screwdriver might be necessary when replacing this part if it becomes broken or bent. This part is made out of metal and is available individually.