This part comes directly from Breville. This Core Gear is used in the Breville 800CPXL Citrus Press. This Gear is made of a hard plastic and is one of three gears that drive the Reamer (part number SP0000024). If the Reamer stops turning while the motor is still on, then one of the gears have stripped out and have lost teeth. Replacing the Gear will require the use of a Philips head screw driver.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Perfect replacement part
I echo the reviewer on procedures for installation. Added a little grease between the rubber motor mount and its footing to hold it in place as I put everything back into order.
Good product.
Guest - December 21, 2020
Verified Purchase
★★★★★
★★★★★
Excellent site for parts, keep it up!
Not only that I did not expect to find this part but, works excellent.
Guest - May 24, 2022
Verified Purchase
★★★★★
★★★★★
Great part. Did fit just well.
My juicer is working like new again :-)
Iglobal - May 30, 2023
Verified Purchase
★★★★★
★★★★★
this is the part that i expected
this is an international shipment and the part arrive in good condition, on time and it is the rigth one.
thank you.
Iglobal - October 28, 2019
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1. Removed the 3 screws at the bottom of the juicer.
2. Removed the lit and disengage the wiring.
3. Removed the screws on top of the motor.
4. Open the motor and pop the gear out.
5. Replaced and reassembled.
In order to open the device I removed 4 screws from the base. This was the most difficult task. In order not to ruin the screws I used Impact driver and torque bit. The same tools are needed to replace the screws. The other part of the repair was easy and involved removing 4 screws to remove the gear cover and replacing broken gears with
... Read morethe new ones and lubricating.
1. Remove the bottom plate from the unit covering the power cord entry (2 screws).
2. Remove the three screws holding the case and motor together.
3. Remove the top casing. I disconnected the wire to the engage switch.
4. Remove the old gear.
5. Clean any nylon chips from the gear cavity.
6. Lubricate the
... Read morenew gear and replace it. I used grease from the cavity.z
7. Reconnect the engage switch wire.
8. Position the motor (there is a rubber bumper that needs to be placed correctly).
9. Position the top plate onto the case.
10. Replace the case screws.
11. Replace the bottom plate.
12. I removed the handle and cleaned the juice splatter from the inside portion of the handle, you have to push in the spring loaded catches to do this.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
