It is a genuine item that is supplied directly from the original equipment manufacturer for use with Echo and Shindaiwa lawn and garden equipment. This special component is utilized to provide a tight seal between connected parts, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind over time the material may wear out and crack eventually requiring a replacement. It is a high-quality seal which is made of durable material is sold individually.
I disassembled the gearbox and removed worn gears. Then I removed the blades. The next step was simply reinstalling the new parts. I greased the gearbox and adjusted the blades to the correct tightness. Then I sprayed lubricant on the blades and started it up. It worked perfectly.
Did you find this story helpful?
Thank you for voting!
Sickle blade struck an object and bent the 1/2\" X 1\" gear shaft
Completely dismantled trimmer to replace gear box then reassembled using all the parts ordered. I had to be careful reassembling the blades as the two gears had to be installed 180 degrees so blades would oscillate as designed otherwise the gear shaft could be bent again when starting engine.
I used a hex wrench to remove screws of gear case cover. Placed the missing seal (used a small flathead screwdriver to push it in place in order to close cover). Replaced worn gasket and added grease. Used a phillip screwdriver to remove handle screws and replaced broken throttle lockout.
1-Remove lower housing plate (8 hex bolts) and remove the 2 10mm bolts closest to the gear box.
2-Remove spur gears(2). Make note of how gears an washers are placed.
3-Clean out old grease.
4- Make sure all broken gear teeth are removed. Use a telescopic pen magnet.
5-Replace washers and new gears and seals. Finger
... Read more lube with grease from grease gun.
6-Refill gear box with grease gun.
Read less
Did you find this story helpful?
Thank you for voting!
Gear tooth busted on transmission in hedge trimmer
Removed Cutting bar and hex head screww holding case. dissassembled gear case and removed broken gear. Cleaned out old grease with metal chips. reassembled new gear and sealed case with grease.
Did you find this story helpful?
Thank you for voting!
Gearbox had become loose and cutter arms were vibrating. One gearbox screw was missing.
1. Removed gearbox cover.
2. Retighten cutter bar bolts after re-applying grease to both bars.
3. Removed and replaced gearbox Gasket and Seal.
4. Repacked grease in gearbox.
5. Replaced gearbox cover with new gasket.
6. Replaced missing gearbox screw.
7. Replaced gearbox screws that showed wear.
... Read more>8. Torqued all screws and bolts.
9. Tested Hedge Trimmer for proper operation and clearance.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP9047135
Manufacturer Part Number: 61042606560
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Seal or Gasket","title":"Seal or Gasket","url":"/parts/lawn-and-garden/hedge-trimmer/seals-and-gaskets/"},{"position":2,"name":"61042606560","title":"61042606560","url":""}]
_WW_12.gif "Part Location Diagram of 61042606560 Shindaiwa Seal")
_WW_12.gif "Part Location Diagram of 61042606560 Shindaiwa Seal")
