The spike is designed to provide a tight grip on the material when performing a cutting job. This is a genuine manufacturer-supplied component that is made for use with Poulan, Husqvarna and Jonsered chainsaws. It is a high-quality replacement for a missing or a damaged part that was installed on a new unit. To ensure the proper replacement and the correct application, check the owner's manual and the diagrams for your model. Note, one durable metal spike and two screws to secure it are included. A screwdriver will be needed to repair this component.
Troubleshooting
This part works with the following brands:
Husqvarna
Poulan
Jonsered
Craftsman
RedMax
This part works with the following products:
Chainsaw
Part# 530014381 replaces these:
530014381, 530014469, 530038990,
Videos For installing this part.
?
★
Customer Part Reviews
?
4.8
Average Rating (out of 5):
★★★★★
★★★★★
(6 Reviews)
Click to filter by ratings:
5 stars
5
4 stars
1
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Spike
Fit perfectly and got in a few days
Guest - June 12, 2020
Verified Purchase
★★★★★
★★★★★
Fit and worked as intended.
My saw never had this spike installed (must have been an option) so I wasn't sure what would be needed to install. Turns out, no problem, saw was prepared for this accessory.
Gary - July 14, 2020
Verified Purchase
★★★★★
★★★★★
The right part of good quality
The part arrived quickly in excellent condition in Switzerland.
Iglobal - October 21, 2020
Verified Purchase
★★★★★
★★★★★
Too long Delivery!
The part ordered was fabulous, but it took way too long to deliver it, can't wait this long to get parts, I have too many repairs on the bench at one time!
Ronald - November 12, 2022
Verified Purchase
★★★★★
★★★★★
the right part for the job
been ordering parts from you for a long time and no disappointment's yet good job!
Guest - November 25, 2024
Verified Purchase
★★★★★
★★★★★
chainsaw
spikes fit great, screws are alittle small
spikes
Guest - March 6, 2023
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1. Remove bar and chain
2 . Clean out holes where spikes mount ( air compressor or compressed air in a can works also )
3 . Install spike with supplied Allen screws
4 . Reinstall bar and chain and tighten
5. Enjoy the new installed spike
Did you find this story helpful?
Thank you for voting!
Nothing was wrong I just needed the spike assembly for my saw.
Replace kill switch lever.
1. Removed engine cover
2. Used nut driver to remove switch lever being careful not to brake metal spring with kill wire attached.
3. Installed new switch lever while carefully reinstalling spring with kill wire.
Note: there is no reason to remove carburetor to perform this repair.
... Read more/>Installation of spike
1. Remove clutch cover, bar and chain.
2. Place spikes on area provided on saw.
3. Drive the short screw into one of the holes provided on the saw. Note: one of the screws provided with the part is not correct for my application(Husqvarna 240)! Had to drill the upper hole location with a drill bit no larger than pilot hole and provide my own short screw.
4. Make spike screws snug. Do not over tighten as you can strip the plastic on the saw!
Removed the bar and chain, removed the two screws holding the remainder of the bumper installed the new bumper with the new screws that came with the bumper witch I thought was cool because they get worn if you\'re like me and remove the bumper on occasion to get a good cleaning the mount area, over all I would recommend using ereplacemen
... Read moretparts.com because it arrived on time fit good and came with instructions not needed in this case but could be helpful for more complicated repairs
Read less
Did you find this story helpful?
Thank you for voting!
It came through without the bucking spike on the saw
1) Loosen and remove the cover that allows you to access the bar and chain.
2) Remove the bar and chain.
3) Install the spike with the screws provided and tighten.
4) Reattach the bar, chain, and cover, being sure to properly tighten the chain before use
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP9284963
Manufacturer Part Number: 530014381
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_12.gif "Part Location Diagram of 530014381 Husqvarna Spike 36/41")
_WW_12.gif "Part Location Diagram of 530014381 Husqvarna Spike 36/41")
