This is a genuine part which is specially designed for Toro walk-behind lawn mowers. Mower cables can break through normal use. The ends can snap off, or the cable can kink or fray. Replacing a broken cable is an easy way to keep the mower running. This cable connects to the control bar that is used to run the engine and when it is released the engine shuts off. Over time it may wear out or get damaged eventually requiring a replacement. Refer to the appropriate diagrams for your model to ensure the correct repair procedure. Note, this high-quality rubber insulated cable assembly is sold as an individual item.
Troubleshooting
This part works with the following brands:
Toro
This part works with the following products:
Lawn Mower
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Removed rear wheels to get better access
Removed battery tray
Removed cover under the mower
Removed old cable
Installed the new one
Reassembled the mower
It is better if gas tank is empty and be sure spark plug is disconnected
Mower works fine
Parts ordered fit perfectly
Remove gasoline from tank.
Disconnect spark plug wire.
Remove battery/box (# 25 torx screws). Note: battery polarity (red +).
Put mower on its right side on (walk-around) surface or ground.
Remove blade (9/16GÇ¥) and disk.
Remove 3 ea shroud screws (3/8GÇ¥) from top of deck, 1 ea from bottom.
Lift shrou
... Read mored at shaft end and pop shroud lip down and away from frame.
Remove cable anchor (7/16GÇ¥) nut.
Unhook tension spring from the brake slide control.
Snake the spring and cable up through the grommet hole to the bail-brake, noting the anchor routing and zip tie locations on the mower frame.
Pry speed nut cap off the bail handle (reuse nut), rotate cable up 90 degrees and slide cable off the handle.
Reverse the procedure to install the new cable.
Hook spring on brake control slide.
Install new grommet (supplied on new cable).
(Nylon web on new cable spring keeps grass out of spring.)
(The Cable Asm rotates the friction brake (blade) away from the pulley.)
Install and temporarily tighten* cable anchor nut .
*Have assistant squeeze brake lever on handle and adjust the length of cable from this anchor to the spring to just release brake but not to over stress cable.
Reassemble disk/blade, shroud, battery box, zip ties, etc.
Connect spark plug and battery cable.
Start and test:
Engage brake bale, the blade rotates and the engine rpm increases to cutting power.
Releasing the bale will engage the brake causing engine rpm to idle.
1. Removed fluids from engine
2. Put mower upside down on sawhorses.
3. Removed rear wheels to gain access to drive shroud bolts.
4. Moved battery box to gain access to one of the shroud bolt.
5. Removed remaining shroud bolts.
6. Removed shroud.
7. Removed cable connection and removed from mower.
<
... Read morebr />8. Installed new cable assembly.
9. Installed spring in handle.
10. Reassembled everything.
11. Replaced fluids in engine and gas in tank
12. Tested the repair. Successful
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP9257122
Manufacturer Part Number: 107-0799
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
(2006)_WW_13.gif "Part Location Diagram of 107-0799 Toro Cable Asm")
(2006)_WW_13.gif "Part Location Diagram of 107-0799 Toro Cable Asm")
