Ensure optimal cutting performance with this authentic OEM replacement blade drive belt, designed specifically for use with riding lawn mowers and garden tractors. Unlike aftermarket alternatives, this belt is sourced directly from the original equipment manufacturer, guaranteeing a precise fit and reliable operation.
This is the main belt responsible for driving the mower blades, making it a critical component for efficient mowing. Constructed from durable rubber, it’s built to withstand the rigors of regular use but should be inspected periodically for signs of wear or stretching. When it’s time for a replacement, be sure to clean the pulleys thoroughly before installing the new belt—this helps maximize performance and extend the life of the part.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Belt was just as ordered. This was the oem belt. Heavier than aftermarket belts
Fit perfect. Installation was fairly easy. Belt arrived in about 4 days.
Guest - October 1, 2019
Verified Purchase
★★★★★
★★★★★
Simple deck belt
Always receive parts in a timely manner and always correct Thank You
Guest - April 18, 2020
Verified Purchase
★★★★★
★★★★★
Great part worked with my Bolen lawn tractor.
This part and all the other parts that I have ordered work great. I have fixed the transmission, changed blades and belts and my mower works like new. Great service
Guest - May 6, 2020
Verified Purchase
★★★★★
★★★★★
Original part
Good
Guest - May 27, 2020
Verified Purchase
★★★★★
★★★★★
Great part
Belt arrived earlier than expected. Fit perfectly. Lawnmower working well
Guest - June 23, 2020
Verified Purchase
★★★★★
★★★★★
Unfortunate repair
Replaced the belt. When I started my Bolens riding mower the belt came off the drive (motor) pulley. Upon examination I found that the belt was badly damaged and not usable. Further investigation found the the tension spring on the variable tension pulley was broken on one end (disconnected). I found a replacement spring locally and another new belt. Replaced both of these and the blades seem to be engaging OK.
Guest - September 19, 2021
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
First I had to raise the rear of the tractor an remove the rear wheels. Remove the bearing cap an bearings from bottom pulley. Remove nut on top rear pulley both at rear of tractor. Then I removed the spring tensioner from the drive belt.Remove old belt an thread new belt up an around front pulley on motor that way you don\'t have to remo
... Read moreve pulley on motor. Put the new belt on pulley and replace pulleys. Attach tensioner spring. Put wheels back on.To install new cut belt I just had to remove two pulley guards an remove one tensioner pulley.The pulley was held on with a nut an bolt, both very easy to get at. Remove old and replace new. Remember placement of belt to insure proper placement.The belt will fit in other ways but will only work in proper direction.Oops.Replace one pulley and pulley guards.No need to remove any springs in this application. You are ready to cut. The hole process took about 1-1/2 hours. It is best to have 3/8 an 1/4 inch socket sets.The 1/4 inch set works best on the cut deck.
Removed the battery, removed the pulley with 7/8 claw socket, installed the belt on the pulley and reinstalled the pulley to rear ended. Then, installed the battery and made a test run on the lawn mower.
1. Lowered deck
2. Moved fuel tank to side.
3. Used #4 phillips bite with brake over to remove hex patch bolt from shaft lower mount point.
4. Remove steering wheel center cover and bolt/remove wheel
5. Remove old shaft; grease gear on new shaft an install with new hex patch bolt.
6. All spacer and washers we
... Read morere ok.
Read less
Did you find this story helpful?
Thank you for voting!
V-belt was worn out/stretched and the idler pulley was bent and had jagged edges
1. Removed deck from the mower for easier work space.
2. Removed idler pulley and v-belt.
3. Installed the new idler pulley and v-belt to the mounting arm.
4. Installed the deck to the mower, checked all connections, leveled the deck per the instructions.
5. Started and tested in a safe area away from the house and
... Read more any other persons.
6. The parts worked great, operates like a new mower.
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
