This is a genuine manufacturer-sourced replacement part which is specially designed for use with Toro and Lawn Boy lawn mowers. The traction cable engages the drive wheels, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality rubber insulated part is sold individually.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Right Part
Easily able to order the right part, shipped fast and was simple to install.
Stephen - August 26, 2019
Verified Purchase
★★★★★
★★★★★
Great
Grear
Guest - June 20, 2020
Verified Purchase
★★★★★
★★★★★
My lawn mower is fixed
My third order after talking to a customer service person was correct. I ordered the wrong cable using the web site by myself. My returns were credited and I received the correct part promptly.
Pat - December 23, 2020
Verified Purchase
★★★★★
★★★★★
Helpful Part Info, Fast Reliable Service
I will remember your service when my next replacement part is needed. Keep up the good work.
Guest - May 22, 2021
Verified Purchase
★★★★★
★★★★★
Easy repair
Order was shipped right away and also received email on how to install which was very helpful for me. Mower is working great again. Customer service was very helpful.
Guest - August 11, 2021
Verified Purchase
★★★★★
★★★★★
Mower repair
Arrived in reasonable amount of time - replaced and back to mowing!!! Thanks for the great service!
Guest - October 21, 2021
Verified Purchase
★★★★★
★★★★★
Great!
Got it in good time and works like it should!
James - November 10, 2021
Verified Purchase
★★★★★
★★★★★
Mower part
The part arrived quickly and back working
Guest - May 21, 2022
Verified Purchase
★★★★★
★★★★★
Prompt shipping, received as advertised.
Received as advertised. Perfect fit. Shipped in 1 day
Guest - April 24, 2023
Verified Purchase
★★★★★
★★★★★
Not sure if wrong part was pulled. I was looking for a adjustment but didn't see one. The cable was too long not right part.
Wrong part I think the cable was too long, from back wheel to upper handlebar
Guest - May 20, 2019
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1. Cut cable off on top of mower deck
2. Drained gas out of tank
3. Turned mower on its side and unhooked cable
4. Pushed cable thru mower deck and attached new cable to bracket
5. Turned mower over and undid bracket holding cable and removed old one
6. Installed new one and attached it to control bar befor
... Read moree reinstalling bolt to hold it to mower handle.
6. Put a small amount of gas and started the mower and checked out the self-propelled option.
Remove spark plug wire drain fuel from mower. Remove baffle cover there were five 10mm bolts holding mine. On disconnect spring end of cable from drive belt assembly remove hold down bolt for cable at top of control handle. Unclip cable from mower deck with pliers, its plastic just squeeze it. Remove cable reinstall new one reversing remo
... Read moreval instructions, adjust cable for proper motion speed by moving it up or down through the hold down bracket at top of control handle, and your done test mower for proper operation after you finish
1. Remove the right rear wheel, a deep socket required
2. Remove two screws from the plastic shroud nearest the traction cable connection, inside & under
mower deck.
3. Loosen the traction cable clamp located on the left side of the mower handle to make room for
the replacement cable.
4. Work loose the old
... Read more traction cable from the mower deck, may require a screwdriver to \"snap loose\"
the plastic plug holding it in place.
5. Remove the old traction spring from the traction lever.
6. Thread the new traction cable through the mower deck, pull back the plastic shroud to make room
to connect the traction cable spring into the traction lever. (The most difficult task involved)
7. Replace all screws, wheel
8. Tighten the traction cable clamp located on the left side of the mower handle, check cable length.
9. Inspect, reinspect, rejoice.
10. Pay the next door neighbor kid to mow your lawn with your newly repaired Lawn Boy knowing you saved $100 in repair costs and two-three weeks in the repair shop.
Removed the broken cable and attached the new. Had trouble getting the broken one off but took about 10 minutes to replace it. Thank you E replacement parts. Saved me about $60.00.
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP8843774
Manufacturer Part Number: 112-8817
Lawn Mower
- Toro Lawn Mower Model 29643/SERIAL: 313000001-313999999 (29643/SERIAL:313000001313999999, 29643/SERIAL: 313000001 313999999) Parts
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
(2012)_WW_3.gif "Part Location Diagram of 112-8817 Toro Cable-traction")
(2012)_WW_3.gif "Part Location Diagram of 112-8817 Toro Cable-traction")
