Close
Phone 1-855-343-0069
Cart
Official OEM Guarantee
Fast shipping from USA
365 Day Returns
Preferred Brand Partners
8774797-1-M-Ariens-00428700-Bearing Flange
Part Location Diagram of 00428700 Ariens Bearing Flange
See part A-2 in the diagram
( Grid squares measure 1x1 inch )
8774797-1-S-Ariens-00428700-Bearing Flange Part Location Diagram of 00428700 Ariens Bearing Flange

Bearing Flange 00428700

Manufactured by:
Ariens
ERP Number:
ERP8774797
Part Number:
00428700
Original Equipment Manufacturer ?
$27.56
Special Order

Easy 

1- 2 hours 

(1 rated repair) ?

Does this part fit my model?

Need help finding your model number?

Jump to:

Questions & Answers Repair Instructions

Troubleshooting

This part works with the following brands:
  • Ariens
  • Gravely
This part works with the following products:
  • Snow Blower

Questions & Answers

?

Our customer Service team is at the ready daily to answer your part and product questions.

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Ask our Team

We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

Does this fit my product?

Customer Repair Instructions

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

Easy 

1- 2 hours 

(1 rated repair) ?
  • 1
Sort by:  
Sorry, we couldn't find any existing installation instruction that matched.

Auger drive shaft bearing disintegrated resulting in both drive belts being destroyed

Wayne from Medway, Massachusetts

2 of 2 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Parts Used:
07200431, 05409300, 01014200, 00428700
1. Removed the belt cover and then the bolts holding the auger housing to the engine housing and hinged the auger away from the engine.
2. Removed the old belt pieces and the double pulley from the shaft mount. Backed the shaft mount screw out half an inch.
3. Used a steering wheel puller and three bolts to pull the pulley sh aft mount from the auger drive shaft by pressing on the shaft mount screw.
4. Removed the bolts holding the horizontal auger shaft from each side of the auger housing and removed the bolts from the auger gear box and the support bracket. Slid the auger assembly out of the housing.
5. Removed the old bearing brackets. Removed rusty areas on the housing followed by priming and two coats of matching paint to inhibit further rust.
6. Installed the new sealed bearing using new brackets but left the bearing loose in the brackets. Slid the auger assembly back in place and installed all the mounting screws finger tight.
7. Tightened the bearing brackets and auger mounting bolts and checked free rotation of the auger.
8. Installed the pulley shaft mount after applying white lithium grease. Installed the double pulley wheel.
9. Hinged the auger housing and engine housing back together and bolted it in place.
10. Loosened the tension adjustment bracket on the belt idler and installed the new belts.
11. Tightened the tension adjustment idler until they would engage and disengage properly with the control lever.
12. Put the belt housing cover back on and tested the operation.
Read less
Did you find this story helpful?
Thank you for voting!
  • 1
Bearing Flange
$ 27.56
Special Order
✖
Stock Status
✖
Mail-In Recycling Rebate

Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.

✖