This carbon brush set is an authentic OEM sourced part, it is not an aftermarket imitation. It is commonly utilized on Bosch and Skil power tools. Over time brushes will wear away requiring replacement. This set includes (2) brush holders and (2) carbon brushes with lead wires and springs attached. You will need a screwdriver to complete this repair.
Troubleshooting
This part works with the following brands:
Bosch
Skil
This part works with the following products:
Jig Saw
Orbital or Palm Sander
Saw
Part# 2609120199 replaces these:
2609120199,
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(4 Reviews)
Click to filter by ratings:
5 stars
4
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Parts was exactly had described
Good price... would use this saller again
Guest - September 26, 2019
Verified Purchase
★★★★★
★★★★★
Came in a hurry.
Sander went down in the middle of sanding boat for fiberglass/epoxy coat. Stalled production as backup sander was at son’s cabin for other work. Four days later I was back up and sanding. Great service!
Guest - November 17, 2020
Verified Purchase
★★★★★
★★★★★
brushes
Just as advertised
Guest - March 3, 2022
Verified Purchase
★★★★★
★★★★★
Correct part
The web site made it easy to find the parts I needed. They arrived fast and they were the correct ones.
What more can you ask for!
Bill - May 3, 2023
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
I removed screws from sander housing and handle, separated and lifted the screw side of housing to expose the carbon brushes. Since the original brush holders had removable and reusable electrical wire connections, I removed the old brushes and tension springs and replaced them with the new brushes and springs. By reusing the original bru
... Read moresh holders, I did not have to cut an wires, do any splicing, or do any soldering. The new brushes and springs fit perfectly in the original holders. I reassembled the sander housing while carefully ensuring the brushes and all electrical wires remained in place. I replaced and carefully tightened all the housing screws.
1. Removed sander top cover.
2. Removed old brush spring and metal clip.
3. Installed new brushes. Note: They install in a sideways direction.
4. Replaced sander top cover.
Being novices at tool repairs, the hardest part of the repair was getting the sander apart completely and the wires to the brush arms were in a very tight space, getting them back in place after putting the new brush arms in so the sander would close took the most time. Taking pictures while taking the sander apart would have helped us r
... Read moreeassemble after the repair and saved a lot of time.
The switch was the easiest part of the repair. The dust cover on the switch was worn off completely and that may be what the problem was, dust got in the switch.
We also use compressed air in a can to clean all the wood dust out which had accumulated over 8 years! The parts were good and effective and the sander runs powerfully again and really collects the wood dust. Ereplacementparts has helped us to do our own repairs and be able to use our tools a lot longer.
Read less
Did you find this story helpful?
Thank you for voting!
The jig saw was gradually slowing down and sparking at the brushes. Eventually it came to a total halt.Upon inspection both original brushes were worn completely down.
The saw case comes apart by removing several screws and removing one half of the case. Then the brushes can be lifted out and the wires detached using a pair of needle noses pliers. Reinsert the new brushes , perfect match, and reassemble the case. Back in business!
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP19510016
Manufacturer Part Number: 2609120199
Orbital or Palm Sander
- 5 in. Variable Speed Palm-Grip Random Orbit Sander
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
