Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Saved my Delta 28-303 Type 1 band saw from the trash heap.
Thought the saw was destroyed when a heavy box was set down on the fence support rails and both trunnions broke. These trunnions fit perfectly and seem to be quite a bit heavier duty than the originals. It was fairly simple to pull the angle scale off the old one and drill the holes for #4 button head screws to hold it on the new one.
Guest - August 9, 2019
Verified Purchase
★★★★★
★★★★★
great part and fast delivery!!!
the trunnion I got for my delta drill press fit perfectly-fast service and was easy to install
Guest - November 14, 2019
Verified Purchase
★★★★★
★★★★★
Worked perfectly on Delta band saw
These were used on a Delta band saw which had no replacement parts available, but based on recommendation from another review, it was stated these would work. The worked perfectly and were much heavier duty and fit right on the Delta unit.
Guest - December 3, 2019
Verified Purchase
★★★★★
★★★★★
The part arrived exactly as your communication said it would. Our trailer is still in winter storage, so haven't made the repair yet.
Looks good, but can't put it in till we get our trailer home in April.
Guest - March 23, 2021
Verified Purchase
★★★★★
★★★★★
Very helpful, friendly people.
All good
Guest - October 5, 2019
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
I did my research on the internet and found out that the parts to repair my saw were no longer available. I researched for several months and found out that the trunion for a powermatic 14 inch bandsaw would fit. Ordered them and put them on (20 min job) and presto changeo I have aworking saw.
Remove trunnion clamp base from underneath the table. remove trunnions and clamp shoes from the table. Attach the new trunnions and clamp shoes to the table. The attach the clamp shoe base to the table.
Remove the table from the saw
Removed old trunnion pieces
Moved degree sticker to new trunnion
Replaced with new trunnions
Put the table back on the bandsaw
Easy fix..parts fit perfectly and were cheaper than other sites.
Removed broken attached original trunnions and replaced them with the replacement after market trunnions. Seemed to be of better quality than the originals.
Did you find this story helpful?
Thank you for voting!
Broke trunnions with too much downward pressure on band saw table.
I see trunnions have been re-engineered and much stronger it appears. Metal thickness is greater. Original trunnions very thin. Very easy. 8 fasteners and done.
Remove: band saw blade, insert plug, and insert pin
Loosen table fasteners
Remove broken trunnion
Install new trunnion, be careful not get it too tight
Reassemble table
Reinstall blade and other components
Adjust table for square
Did you find this story helpful?
Thank you for voting!
Well my inexperiance in moving equipment started the problem, Should have removed the cast iron table for transporting. Anyway broke the trunnion.
Vary easy to repair, remove table position bolts, remove trunnion bolts , replace trunnion and put bolts back in. I\'m up and running again. This trunnion fit my CalHawk 14\" band saw.
Did you find this story helpful?
Thank you for voting!
The Trunnions under the table broke during our move.
Finished removing the table. Put the table one the bench. Removed the bolts holding the old trunnions. Cleaned the area around the trunnions and bolted down the new trunnions. Reinstalled table back on to the saw.
1. Removed broken trunions from table
2. Cleaned out all broken pieces from saw
3. Installed new trunions and shoes to the table
4. Installed table to the saw.
The powermatic trunnions are much heavier duty than the Delta original parts and shouldn\'t break.
1. Disconnect power to bandsaw
2. Remove blade
3. Remove table
4. Remove six table bolts from underside of table
5. Remove two table adjuster knobs and associated hardware
6. Remove any remaining trunnion pieces
7. Install trunnions to yoke on bandsaw paying attention to the bolt pattern on the table
... Read morer />8. Place table on trunnions
9. Hand start all table bolts. The two innermost bolts will be very difficult to install if any bolts are tight before starting these two. Hand start all the other bolts first, then these two.
10. Tighten all table mount bolts
11. Replace blade
12. Restore power to bandsaw.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP19189969
Manufacturer Part Number: PM9-PWBS14-144
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_3.gif "Part Location Diagram of PM9-PWBS14-144 Powermatic TRUNNION")
_WW_3.gif "Part Location Diagram of PM9-PWBS14-144 Powermatic TRUNNION")
