Close
Phone 1-855-343-0069
Cart
Official OEM Guarantee
Fast shipping from USA
365 Day Returns
Preferred Brand Partners
Part Location Diagram of JT9-708015-112 Jet WATERPROOF ON/OFF SWITCH
See part A-12 in the diagram
Part Location Diagram of JT9-708015-112 Jet WATERPROOF ON/OFF SWITCH

WATERPROOF ON/OFF SWITCH JT9-708015-112

Manufactured by:
Jet
ERP Number:
ERP19137967
Part Number:
JT9-708015-112
Original Equipment Manufacturer ?
$16.49
Special Order

Easy 

15 - 30 mins 

(2 rated repairs) ?

Does this part fit my model?

Need help finding your model number?

Jump to:

Troubleshooting Questions & Answers Repair Instructions Model Cross Reference

Troubleshooting

This part works with the following brands:
  • Jet
This part works with the following products:
  • Bench Grinder
  • Shaper
Part# JT9-708015-112 replaces these:
708015-112,

Questions & Answers

?

Our customer Service team is at the ready daily to answer your part and product questions.

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Ask our Team

We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

Does this fit my product?

Customer Repair Instructions

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

Easy 

15 - 30 mins 

(2 rated repairs) ?
  • 1
Sort by:  
Sorry, we couldn't find any existing installation instruction that matched.

Sharpener stopped working, speed control circuit board bad

Stephen from AUGUSTA, Georgia

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
JT9-708015-116, JT9-708015-112
1. Removed 4 screws holding speed control - on/off switch face plate to power box
2. Disconnected power wires from on/off switch & removed wires from old circuit board after removing it from the power box, popped existing on/off switch out of face plate
3. Assembled new speed control to face plate, adhered new label & secured new knob with allen screw (allen screw is extremely tiny, be careful not to drop it)
4. Removed existing wires from old circuit board & installed on new circuit board
5. Screwed new circuit board in place inside power box
6. Snapped existing on/off switch into new face plate & re-connected power wires
7. Re-installed speed control - on/off switch face plate to power box
8. Plugged in power cord & tested sharpener to run properly & confirm correct direction of wet stone rotation
Read less
Did you find this story helpful?
Thank you for voting!

Unit would not power on.

Mark from Milaca, Minnesota

0 of 1 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
JT9-708015-116, JT9-708015-112
I removed the control board and the speed adjusting switch set. I replaced them with new parts from eReplacements and I also replaced the waterproof switch. After this the machine powered right up and back to sharpening and polishing again.
Thanks for the service and the right parts!!!
Did you find this story helpful?
Thank you for voting!
  • 1

Model Cross Reference

This part works with the following models:
ERP Number: ERP19137967
Manufacturer Part Number: JT9-708015-112
Brand Model Number Description
Jet 708015 Shaper - Jet 708015 Parts
Jet JSSG-10 Bench Grinder - Slow Speed Wet Sharpener
WATERPROOF ON/OFF SWITCH
$ 16.49
Special Order
✖
Stock Status
✖
Mail-In Recycling Rebate

Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.

✖