Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Repair went well
All went as planned. Good replacement. Easy to obtain from this company. Thanks.
Guest - July 8, 2019
Verified Purchase
★★★★★
★★★★★
Great How-to Video and Service
Watched the ereplacement's video on how to replace the coil spring on my drill press, then ordered the part.. Received very quick service on mailing and receiving the part. Drill press back in service.
Guest - September 1, 2020
Verified Purchase
★★★★★
★★★★★
Easy repair and easy install
It was an exact replica of the original one.
Guest - December 14, 2022
Verified Purchase
★★★★★
★★★★★
The video helped the repair. Get a spare!
eReplacements took their sweet time filling the original order I placed for this spring. My shop (spec. Jet Drill Press) was hampered for several weeks waiting for it to arrive. I only learned after the break in this new drill press that it happens with lots of use. Mine is in production mode most days. Since I cannot wait for eReplacements to keep in production I have ordered another spring as a backup so I am ready immediately next time it breaks. eReplacement video was helpful, however, my model Jet DP does not have the swing-out depth stop like the one in the video. It takes a bit of finesse to tighten the spring to the correct "feel". Use a small straight screw drive in the spring loop. Good luck.
Guest - June 7, 2023
Verified Purchase
★★★★★
★★★★★
Great Part
The part came quickly and installed easily!
Guest - August 24, 2023
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Unplugged the Drill Press
Removed the Chuck(less weight to hold while twisting up the spring)
Removed the spring cover (two nuts)
Removed the entire assembly to inspect clean and lube
Re-inserted assembly
Aligned spring with slot in shaft
Twisted up spring until assembly would stay up
Used origin
... Read moreal Big Inside Washer, new one supplied didn\'t fit
Re installed two nuts, tightened
Re- install Chuck and Ops Check
1. Removed the two nuts holding the coil spring and cover in place.
2. Installed the new coil spring and cover.
3. Started the first nut by hand to keep the coil spring from falling off.
4. Twisted the coil spring to put tension on the assembly until the tension was enough to bring the quill up and hold it in place.
... Read more/>5. Tightened down on the first nut but not so much that it didn\'t allow the spring to move freely.
6. Added the second locking nut holding the first nut in place.
1. Lock spindle in up position.
2. Remove spring cover retaining nuts (2)
3. Remove old broken spring.
3. Insert new spring align onto shaft.
4. Replace spring cover plate.
5. Adjust spring tension
6 Thread retaining nuts onto spring shaft.
7. Tighten nuts.
Replaced Rack- use allen wrench to loosen 2 allen screws that tighten drill press head to the post, remove drill press head (it\'s heavy get help to lift it) lift head off post, you can then remove rack ring by loosening set screw and slide it off post, then slide drill press table and rack off post together, replace old rack with new, th
... Read moree rack can just be lifted out and replaced with new rack from drill press table gear. Then hold together and slide table and rack back onto post, note up side of rack by arrow pointing up, then I had to replace my rack ring, if yours is okay just slide it back onto post with bevel facing down to hold rack in place on the angled edge of rack on the top, don\'t slide the ring down to tight against the rack it needs to be able to move freely when swinging the table around the post, tighten ring with set screw. Replaced Coil spring- loosen two nuts that hold coil spring and cover on and remove broken coil spring and cover, install new coil spring and cover, you will have to adjust spring tension by turning cover with spring a notch at a time until desired tightness. Hard to explain, but not really hard to do, I looked at youtube videos and still just had to figure it out as I did it. Good luck.
Read less
Did you find this story helpful?
Thank you for voting!
Coil spring on quill breaks every three or four years. Drill press is fine in all other aspects so $35.00 is a no brainer.
Removed two nuts holding spring cover on. Replaced with new cover containing spring, hand wound to correct tension, pushed mating tab on cover into casting on press and re-installed two nuts.
Did you find this story helpful?
Thank you for voting!
Drill bit moved a litlle to the left before touching wood.
Followed the eReplacement video instructions.
I used a piece of 2GÇ¥ x 4GÇ¥ to keep the drill shaft fixed in the uppermost position (spring uncoiled, m+¡nimum tensi+¦n)
Spring broke on a sears drill press they told me at sears they no longer made it I called replacement parts asked for a spring for a Jet drill press figured the companys didn\'t make the spring some one else did. I was right works great same spring
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Spring or Shock Absorber","title":"Spring or Shock Absorber","url":"/parts/power-tool/drill-press/springs-and-shock-absorbers/"},{"position":2,"name":"JT9-10605002A1","title":"JT9-10605002A1","url":""}]
_WW_1.gif "Part Location Diagram of JT9-10605002A1 Jet COIL SPRING WITH COVER")
_WW_1.gif "Part Location Diagram of JT9-10605002A1 Jet COIL SPRING WITH COVER")
