This is a genuine Ridgid replacement part that has been sourced from the original manufacturer and is intended to be used with table saws. The switch attaches to the front side of the saw and is used to relay electricity from the power cord to the motor assembly. This item is priced as a single item.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Excellent service, exact part, fast shipping!
You will now be my go to source for parts. My experience with your company was outstanding. Thank you!
Guest - June 19, 2019
Verified Purchase
★★★★★
★★★★★
Perfect fit
Part was as described and fit perfect.
Guest - May 28, 2020
Verified Purchase
★★★★★
★★★★★
Rigid table saw did not work
Rigid table stopped working. Saw some burn marks at connections at switch. Purchased new one and replaced worked like a charm.
Guest - July 5, 2020
Verified Purchase
★★★★★
★★★★★
Worked as expected
Was an exact replacement and I was up and running.
Frederick Ellis - May 20, 2023
Verified Purchase
★★★★★
★★★★★
Installation was easy but the wires were very short on the saw itself making it a bit tricky. Advice given was accurate and a colourcode for wiring would be helpful. I found this on line at rigidforum.com .
This switch arrived in a week or so in off the shelf condition it was installed and works fine. Shipping charges could be lower for Canada as it was more for shipping than the part itself. Otherwise a very positive experience.
R. Newman
Iglobal - September 13, 2019
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Remove 4 screws from switch housing.
Disassemble switch into 2 halves by prying the 2 holding tabs away with screwdriver.
Remove the main outer switch assembly.
Record the colors and locations of wires on the remaining old switch lower half.
Record the orientation of the new switch lower half with respect to the ta
... Read moreble/saw.
Disconnect wires from old switch lower half with needle nose pliers.
Hold the electrical housing metal cover plate tightly together with the metal electrical housing with electrical tape.
Disassemble NEW switch into 2 halves by prying the 2 holding tabs away with screwdriver.
Connect wires to new switch lower half with needle nose pliers.
Slide a screwdriver under the new switch lower half and between the connected wires as a support to hold the switch above the side of the machine.
Assemble New Main outer switch assembly by pushing down and snapping together with the new switch lower half in the correct orientation.
Remove the screwdriver used as a support.
Assemble the main switch housing with 4 screws.
Remove the 4 screws holding the switch assembly to the saw take the 4 screws out of the fence storage assembly under the saw to make room to work remove the 4 wire connection from the switch, make a diagram on where the wires go on the switch otherwise you will be looking for a wiring diagram on the internet. Manufacture didn\'t waist any
... Read more money on wire here the wires are very short and have to follow exact path you also need to have fingers the size of a #2 pencil
Removed the fence storage shelf then removed the switch. Wires were very short making it a bit difficult to remove and reinstall. Reinstalled the fence shelf after replacing switch.
1 Removed old switch
2 Unplugged wires two at a time
3 Re-plugged wires keeping the order straight
4 Screwed new switch into place.
1 Unscrewed old hand-wheel
2 Screwed new wheel in place
It all went well. There is not much room to work on the Switch but take it easy and don\'t rush it.
Switch replacement fixed the problem. Saw starts as normal again!
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
