Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Easy to repair.
I just used the screws off of the old assembly to put this one on.
Guest - August 14, 2019
Verified Purchase
★★★★★
★★★★★
Weedester
Exact fit,corrrct parts,excellent quality and friendly service. nuff said!!
Guest - August 17, 2019
Verified Purchase
★★★★★
★★★★★
Spring problems
I had my recoil spring come out and in trying to get it back together was a pain. It worked for a little while but I had more problems. I just went ahead and bought the replacement kit, so easy and a good price to.
Guest - August 20, 2019
Verified Purchase
★★★★★
★★★★★
Facil.de instalar
Llego en buena condicion y en tiempo
Guest - August 31, 2025
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1. Removed old starter shroud using a star bit
2. Removed spark plug with 3/4 inch spark plug socket.
3. Rotate the starter cup while looking looking in the spark plug hole and set the piston at the bottom of the stroke.
4. Insert enough pull starter rope into the cylinder to prevent the piston from raising, thus stoppin
... Read moreg the crankshaft from turning while removing the old starter cup.
5. Remove the old starter cup by twisting it counterclockwise with my hand. No need to use hex wrench on mine.
6. Remove nut plate from old starter cup and place it in the new one.
7. Install new starter cup by threading it clockwise onto the crankshaft and make sure it is tight.
8. Remove rope from cylinder and replace spark plug.
9. Install new starter shroud
10. Go cut weeds
Read less
Did you find this story helpful?
Thank you for voting!
Worn out starter assembly frayed rope failed to reliably retract
Replaced assembly. Had to remove a few screws to remove the old starter, then just reused that hardware to attach the new starter assembly. Works like a charm!
Did you find this story helpful?
Thank you for voting!
The old starter assembly was not turning the motor.
1. Removed the six screws holding the old starter assembly.
2. Lifted old starter assembly away from the motor.
3. Placed new starter assembly where the old assembly was.
4. Inserted and tightened 6 screws to hand tight snug. Over tightening may strip the threads on the plastic housing.
**Note: There are three long
... Read more screws and three short screws. The short screws secure the outer perimeter of the assembly. The long screws secure the assembly around the starter gear.**
Upon disassemble of my Poulan P338PT starter, which had less than 10 hours of use, I\'d noticed that the plastic \"starter cup assembly\" had melted on to the engine starter end of the crankshaft. I called Poulan\'s Customer Service and asked why this happened with so few hrs. of use, and received the response \" just buy another cup asse
... Read morembly.\" at a ridiculous price from them. So, I searched the internet and found ereplacementparts. com. It was not until I studied ereplacementparts Poulan factory parts schematics online that I discovered a small thin washer (that was never installed from Poulan) goes between the crankshaft and the starter cup assembly. To prevent it from contacting the crankshaft and melting it. Thanks to ereplacementparts I figured out what went wrong and ordered the parts that saved me from another break down. Thanks again.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP16365709
Manufacturer Part Number: 545212701
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_2.gif "Part Location Diagram of 545212701 Husqvarna Starter Assembly")
_WW_2.gif "Part Location Diagram of 545212701 Husqvarna Starter Assembly")
