This genuine OEM sourced replacement carburetor is specially designed for use with Craftsman handheld trimmers. The purpose of this part is to mix the air and the gas before the combustible mix goes to the engine. If the engine won't start and the tank is full of fresh fuel or if the engine starts and then quickly dies, the carburetor is likely the problem. This high-quality component has a durable metal body and it is sold individually.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Easy repair
I replaced the carburetor on my weed eater in no time. I simply removed the two bolts holding it to the frame and removed the three fuel and purge hoses one at a time. I reattached each hose before removing the next. This kept me from mixing them up when reattaching to the new carburetor. After they were all attached, I screwed the two bolts back to the frame, snapped on the filter cover and fired the sucker up. I am very pleased with its performance.
Guest - April 19, 2019
Verified Purchase
★★★★★
★★★★★
excellent
great,works better than new
Guest - September 10, 2019
Verified Purchase
★★★★★
★★★★★
Easy to install
The carburetor was easy to install and fixed the problem
Guest - October 26, 2019
Verified Purchase
★★★★★
★★★★★
worked perfect
arrived very quick, no problems at all
Guest - June 30, 2020
Verified Purchase
★★★★★
★★★★★
Machine back to running like new
Exact replacement carburetor for older Craftsman Weedwacker. Prompt delivery, reasonable price. Local repair shop informed me that it would be cheaper to buy a new machine than have them repair!
Guest - June 27, 2024
Verified Purchase
★★★★★
★★★★★
Pylon weed wacker
Needed needles adjusted as I live above 6000 feet
Guest - June 5, 2020
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1. Removed air filter.
2. Removed bolts to carb.
3. Removed fuel lines from old carb. and reinstalled on new carb.
4. Put it all back together, started it and adjusted the idle
Did you find this story helpful?
Thank you for voting!
The motor would fall flat when throttle was applied.
Remove the air box cover and the air filter. Then remove the fuel line from the carburetor and remove the throttle link. Remove the fuel line from the primer. Remove the screw holding the air box and the old carburetor on. Remove the old carburetor, install the new carburetor. Then tighten the screw holding it and the air box. Replace the
... Read more fuel line and throttle link to the carburetor. Then install the fuel line to the primer. Install the new filter and air box cover. Remove the boot from from the spark plug and remove the spark plug from the cylinder . Gap the new spark plug at 0.025 Then install the new spark plug into the cylinder and replace the boot.
Read less
Did you find this story helpful?
Thank you for voting!
trimmer would not continue running when loading changed. ie Heavy vs thin weeds
Removed the fuel tank
Removed carb.
Reassembled with original fuel hoses.
Bought new fuel hose and did it again. Note that a picture would help since the purpose of each unmarked hose is not clearly known. Routing is not obvious when the original hose is gone and new unshaped hoses are all you see
Did you find this story helpful?
Thank you for voting!
Engine would run at idle but shut off when given throttle(lean condition)
Remove the air filter cover, remove 2 screws holding carb on. Remove fuel lines and the throttle from carb paying attention to where they go, then reverse order to install new carb assembly.
Did you find this story helpful?
Thank you for voting!
Weedeater was bogging and could not get full power
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
