This is a genuine Black and Decker part that has been OEM sourced to ensure quality. The carrier assembly is intended to be used with belt sanders. The carrier attaches to the cover plate and the mounting plate. This item is used as the front roller to allow the belt to rotate. This part also includes the lever used to move the carrier to tighten and loosen the belt when changing sanding belts. This assembly is priced as a single item.
Troubleshooting
This part works with the following brands:
Black and Decker
Craftsman
DeWALT
This part works with the following products:
Sander Polisher
Sander
Belt or Drum Sander
Part# 589384-00N replaces these:
589384-00N, P589384-00N,
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(9 Reviews)
Click to filter by ratings:
5 stars
9
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Quick found part I needed and shipped same day
Cyst service was great found the part I needed quickly
Guest - June 27, 2019
Verified Purchase
★★★★★
★★★★★
Worked as expected
Excelent
Guest - August 16, 2019
Verified Purchase
★★★★★
★★★★★
Belt sander tension unit repair
The part arrived within a week, the directions on the website were clear on how to remove the three screws and slide out the belt assembly. The spring was the most challenging part since it had to be compressed as the part slid in. Once it was together, it worked fine. It's too bad they have still use a cheap plastic tab. Otherwise, erplacement parts was great.
Mark - September 12, 2019
Verified Purchase
★★★★★
★★★★★
Black and Decker belt sander
The carrier assembly fit perfect. Sander like new. Shipping was quick-Thanks
Guest - August 13, 2020
Verified Purchase
★★★★★
★★★★★
as described
fast shipping, cheaper than from the manufacturer, solved the problem
Guest - February 8, 2021
Verified Purchase
★★★★★
★★★★★
Great part. Easy to instal
The part was new in great condition and was easy to replace.
Iglobal - March 22, 2022
Verified Purchase
★★★★★
★★★★★
Exact part.
I cannot find myself throwing away tools that are repairable and am thankful EReplacment Parts is there to provide the necessary parts.
Part prices are reasonable and shipping is acceptable.
Thanks.
Guest - May 11, 2022
Verified Purchase
★★★★★
★★★★★
added years of service to an old belt sander
The part fits and works like new, identical replacement
Paul - February 10, 2023
Verified Purchase
★★★★★
★★★★★
Ordered part
The right part for my chain saw and came in good timing.
Guest - August 26, 2023
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
Be the first to ask our experts a question about this part!
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1. Using a torx screwdriver,unscrew the 3 screws that hold the main roller ,carrier assembly housing and bottom plate.
2.Unscrew the belt adjustment knob ,so it is no longer holding the carrier .
3.Gently pull apart the full roller assembly from the main unit body,Be careful not to break the screw holders that fit in the assem
... Read morebly on the main unit .
4. The main drive shaft on the main unit and the drive roller gears are visible ,clean and lube the main shaft and bearing.
5. With a flat blade screwdriver ,place between the carrier assembly housing and the drive roller assembly and pry them apart gently,not to break any plastic parts, slide,the carrier assembly housing of the bottom plate .
6.Press the assembly and compress the spring to remove the assembly from the housing.
7.Insert new carrier assembly and spring back in plastic housing.
8.Reattach carrier assembly housing to drive roller assembly,sliding it back in place on the bottom plate.
9.Clean and lube the drive roller gears .
10.When re attaching the roller assembly , to main unit,remember to replace the adjustment knob spring and screw parts back together, your done.
Read less
Did you find this story helpful?
Thank you for voting!
Handle broke and unable to release carrier to add/remove sand paper
Removed screws slid carrier from base. The most time was spent compressing the spring, I just put it in vise and used 2 zip ties . Then just reassembled it
Sander was disassembled down to the carrier assembly, so replaced part and reassembled, no other adjustments. Hardest part was compressing spring on carrier to install. Had to place carrier in a vice to hold (wear safety glasses!) then compressed with adjustable wrench.
1. disassembled sander - you need a 3\" torx driver
2. smashed the spring in a vice and held it smashed with 2 strong zip ties.
3. placed spring over the tounge of new carrier assembly
4. installed carried assembly
5. cut zip ties to release spring
6. reassembled sander
I can\'t imagine how you
... Read morewould ever get it back together without some method of smashing the spring while you reassembled it.
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
