This is an original part from Ingersoll Rand. The valve seat is compatible with several impact wrenches, allowing the valve to be secured onto the housing interior. A wrench is often necessary for the replacement, and the valve seat is sold individually.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Put my drill back to new.
My part's arrived promptly, and it was super easy to fix my IR drill. I'm grateful for replacement parts to be available. So I bought double of what I needed for the wear part's. Now I just need to find more air tools to repair. Hahaha
Guest - November 23, 2022
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Ingersoll Rand 231G. Remove trigger. Remove air inlet with socket & breaker bar. Remove plate and valve spring. Dump out air valve. Force angled pick down between valve seat and body of the tool, pry out seat. (This is difficult and will take several tries.) The valve seat has a wide-open side and a slightly \"fatter\" side; the open
... Read moreside goes in towards the motor, fatter side towards the air inlet. Lube it with a bit of air tool oil and slip it in; using the biggest socket that will fit down the hole and an extension, press the seat all the way down to the bottom. Drop the air valve in, stem first. Drop the spring in, narrow end down. Reinstall the spring and plate; reinstall the inlet with blue loctite. Reinstall the trigger.
Removed old parts to find out what was broken. Ordered parts , ordering parts was very easy and fast shipping. It took two times to get the parts back in the correct way. Successful the second time and wrench works great.
Did you find this story helpful?
Thank you for voting!
replaced valve seal for IngersolRand 231H impact wrench
Watched a few vids on how to get to this seal - none prepared me for the red Loctite IR used on the threads. After padding out an under-table vice to securely hold the impacter, it took a pretty good tug with a 15\" breaker bar to break loose the nut that holds the air fitting.
Once committed to lean on that nut (the 6 point socket
... Read moreleft it\'s mark on the flats), out comes the spring, the valve piece and then the old seal, which pulled straight out with a hooked tool. New seal pushed in easily with a deep well socket. The valve had sharp edges, so softened any felt edges/corners with a fine file before reinstalling. Cleaned and lubed the hammer mechanism, bearings, and the vanes/pump while at it, so this impacter is good as new again
Read less
Did you find this story helpful?
Thank you for voting!
Air ratchet would run without pressing the throttle
1. Removed roller pins with small punch.
2. Slide out the bottom plastic housing of the ratchet
3. Remove air inlet
4. Remove spring and throttle valve
5. Remove air inlet quantity adjustment knob while making sure not to lose the metal pin
6. The throttle valve seal must be installed exactly the same way
... Read moreitGÇÖs removed or it will leak.
7. Pull out old seal with pick set and install new one.
8. Reverse of steps.
9. After everything is back together the throttle should be able to be pressed and it should spring back. If it doesnGÇÖt the throttle valve seat is either installed wrong or the spring is wrong. Nothing should need to be forced too much into place except the roller pins.
10. When installing the roller pins for the throttle switch and air adjustment knob. Make sure the knob is pointing in the red range marked on the plastic housing of the ratchet. If itGÇÖs pointing outside that range and the pin is hammered in, it will damage the knob.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP12094975
Manufacturer Part Number: 131-303
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
