This is an authentic DeLonghi replacement part that has been sourced from the original manufacturer to be used with espresso/cappuccino/coffee makers. The metal spring is used to provide compression between the diffuser and the valve. This item is available as an individual replacement part.
Using a Phillips screwdriver, remove the screw in the center of the diffuser and remove the diffuser. Using a regular screwdriver, remove the dowel. It may be really tight but should just unscrew. Remove and replace the valve and valve spring sitting on top of the dowel. Replace the dowel and diffuser. It may be necessary to remove the bo
... Read morettom for easier access.
1. Flip the espresso machine upside down.
2. Remove the screen from the steamer assembly using a phillips head screwdriver.
3. Remove the brass valve nut with a flat head screwdriver (a penny also works).
4. Remove the valve spring, ring, and valve using the screwdriver to help pull the spring out.
5. Replace the v
... Read morealve spring, ring, and valve and reassemble the machine.
The hardest part was reaching three screws which secure the top of the machine. It requires a star drive. All of the other screws are small Phillips heads. After you remove those and two on the back, the top will lift right off.
I promise, everything is very intuitive. Unplug the hoses by simply pulling on them, remove the pu
... Read moremp by wiggling it off its rubber mounts and unscrew the water valve connected to the pump the pump. Replace those with the new ones and reverse the process.
I chose to change a few of the other little pieces of tubing, simply because I was under the covers - super simple and cheap.
I also replaced the spring and valve on the head (where the water comes out) to ensure that the new pump didn\'t overwhelm an old valve.
This pump works perfectly in our Delonghi EC702, it actually is an improvement over the original one. With these parts changed, we have a completely new machine!
Thanks eReplacement for the super fast service and clear parts catalog!
Removed the Philips screw while the Delonghi EC15 coffeemaker was unplugged (they are all designed very similar so it applies to many other Delonghi coffee makers), removed the round mesh, then used a flat screwdriver to remove another screw which secures the spring and spring valve. At this time the spring valve with the spring will come
... Read more out. Simply replaced them and reassembled. It\'s important to not screw in the flat screw all the way in as it affects the flow rate of hot water.
It stopped dripping hot water and now works perfectly.
Read less
Did you find this story helpful?
Thank you for voting!
DeLonghi Expresso Maker was leaking steam and water. The frothing wand stopped working.
1. Removed water reservoir.
2. Unplugged unit.
3. Turned upside down on a table.
4. Unscrewed and removed silver diffuser plate.
5. Next, unscrewed a large headed screw with a flat head screw driver. This screw has a hole in the center. This screw holds the valve spring, valve ring and valve in place.
6. Afte
... Read morer removing this large headed screw, I removed the \"old\" valve spring, valve ring and valve assembly.
7.On the small end of the new valve spring I inserted the new valve ring. I then inserted the new valve into the valve ring. NOTE that the valve is made of silicon rubber. After inserting the valve, the rounded head is on top of the valve ring.
8. I inserted the completed assembly from 7. into the chamber or slot.
9. I screwed the large headed screw back in place.
10. I screwed the silver diffuser plate back in place.
11. I attached the water reservoir and filled with water.
12. I plugged the unit back in and turned it on.
13. NO MORE leaking water or steam, and the frothing wand was functional once more.
Read less
Did you find this story helpful?
Thank you for voting!
The machine\'s lower-boiler output valve was leaking before running a cycle due to the lower boiler being broken and the valve spring missing.
1.) Used a 3mm flathead bit on a long, but skinny screwdriver to unscrew the top heating base from the machine via the black base that surrounds where the water outputs.
2.) Used a Phillips Head #0 bit to remove the two small screws on the back of the machine connected to the top heating base.
3.) Removed the top heating base.
... Read more 4.) [CAUTION]If there\'s water still in the boiler, it will leak. If the boiler is hot, steam may exit, so let the machine cool down before continuing this step[CAUTION] Used an H3.5 (Hex) bit to remove the lower boiler from the upper boiler. It may also help to unplug the connectors from the upper-boiler for easier removal. Take a picture as you go to make it easier to put the wires back in the right places.
5.) After removing the upper boiler, remove the lower boiler.
6.) Grab the new boiler and put together the spring valve contraption. Place the valve ring inside the smaller end of the spring, then the valve, and carefully place the spring into where the dowel would go, with the valve going in first.
7.) Then screw in the dowel.
8.) Place the repaired or newly put together lower boiler back into its position.
9.) Screw the top boiler back to the bottom boiler with the H3.5 (Hex) bit. If you removed the wires, place them back in their respectful positions.
10.) Re-attach the top heating base.
11.) Screw the two small screws back into the back of the heating base with the PH#0 bit.
12.) Screw the three screws that connect the black base to the heating base with a 3mm flathead.
Read less
Did you find this story helpful?
Thank you for voting!
Valve deteriorated allowing water leaks on pressure side of the pump. Check valve on boiler outlet leaked.
Replaced valve on outlet side of pump usine screw driver to gain access and needle nose pliers to remove spring clips on water lines.
Removed check valve with blade screw driver, cleaned valve seat with fine grit piece of sand paper and installed new valve.
1. Remove screws where the portafilter goes
2. Remove plate
3. Remove other screwb and had access to old spring and valve
4. Replace new parts
5. Coffee maker kept leaking
6. Clean the circuit with vinegar and water and that stop the leak
1. I simply pushed the knob right back onto the dial. Easy.
2. Next I unscrewed the shower head with a screwdriver then unscrewed the spring screw.
3. This allowed me to pull out the screw and remove the spring and bulb on the end.
4. I placed the new spring on the screw and put the bulb on the end.
5. Screw it
... Read more back into the brew head ensuring the bulb stays inside the spring.
6. Screw the shower screen back on and tighten.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Spring or Shock Absorber","title":"Spring or Shock Absorber","url":"/parts/small-appliance/coffee-maker/springs-and-shock-absorbers/"},{"position":2,"name":"6113211931","title":"6113211931","url":""}]
