This genuine OEM sourced replacement burner tube kit is designed for use with Weber grills. These are the burners that the flames would rise from, the kit includes the crossover tube which allows gas to flow from one burner tube to another. These parts are very easy to install with included hardware and instruction sheet. This kit includes two durable stainless steel burner tubes, one crossover tube and the hardware with the instruction sheet.
Troubleshooting
This part works with the following brands:
Weber
This part works with the following products:
Grill
★
Customer Part Reviews
?
3.0
Average Rating (out of 5):
★★★★★
★★★★★
(2 Reviews)
Click to filter by ratings:
5 stars
1
4 stars
0
3 stars
0
2 stars
0
1 star
1
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Simple repair
Quality part, fair price, arrived ahead of schedule.
Guest - July 1, 2020
Verified Purchase
★★★★★
★★★★★
wrong part
replacement burners were too big. also, the installation instructions were for a generator replacement. sent everything back.
Guest - May 23, 2019
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Had to replace burner tubes on fairly old grill. Screws were difficult to get out but manageable. Directions were a bit complicated but once I understood I breezed right through it.
Did you find this story helpful?
Thank you for voting!
Old burners were clogged and cross burner was corroded beyond use.
I started by cleaning up the inside of the grill. Then took out the cast iron grills, flavorizer bars, under tray. I removed the top control plate on the right, then started to look for nuts and bolts. I found a screw on the ends of the burners on the left side. Thank goodness Webber uses top quality hardware so There was no rotting scre
... Read morews to fight with. I next had to figure out how to remove the control section before removing the burners. Once I figured that out the burners came out with ease. I installed all the new parts in reverse order. This whole project is a very straight forward operation if your good with hand tools. All I needed was a straight screwdriver, 5/16 socket and ratchet with extension, a pair of Chanel locks and a scraper to clean the inside with. The instructions I received with the burner kit were totally useless as they were for another replacement part that had nothing to do with what I was doing. As I said though, THIS job is straight forward.
Removed two screws holding control cover.
Removed two nuts and washers holding venturi bracket.
Slid burners out about an inch in order to remove cross
over tube. Pulled burners out by rotating 90 degrees.
Reversed process with new burners and cross over.
Works great, good flame full length of burners.
Removed worn out tubes and ignitor inside base unit and on the top of the side panel after disconnecting tubes and ignitor box/push button from manifold and side control unit. Cleaned the inside of the base unit. Replaced the parts and reconnected the manifold. Connected ignitor wires through base side into new ignitor switch. Done.
... Read morevery easy.
Read less
Did you find this story helpful?
Thank you for voting!
Gave father in law new Weber 15 years ago for his wife. Needed new burners.lighter
Instructions were clear and fix was easy. FYI, clean grill throughly when parts removed really helps. 60 minutes start to finish. Had some grease cleaner and hot water.
Make sure you measure your burners and grates so you are sure on the model number. Know what models have two or three burners as cross burner arm is different.
... Read more Again, Make sure you have the right parts when you remove them, check them with the replacement parts.
1. Removed the gas tank
2. Removed the burner control knobs
3. Removed the manifold cover and manifold
4. Slid out the old burner tubes.
5. Reversed the entire process after sliding the new tubes in.
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_1.gif "Part Location Diagram of 10459 Weber Burner Tube Parts Kit")
_WW_1.gif "Part Location Diagram of 10459 Weber Burner Tube Parts Kit")
