This is an authentic manufacturer-sourced component which is specially made for DeLonghi toaster ovens. Fuses are generally utilized to block excessive electric current from damaging or overheating other part assemblies along the circuit. It is an identical replacement for a damaged or a missing component that was installed on a new unit. Check the diagrams for your model to ensure the correct repair procedure. A screwdriver will be needed to replace this fuse.
Troubleshooting
This part works with the following brands:
DeLonghi
This part works with the following products:
Toaster Oven
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
You need to remove the side/top of the unit which requires removing all the screws you can see and a few that are a bit hard to find, like the ones in the foot, and those require a special driver from torqx with a triangular head. I was actually able to get them out using a tiny screwdriver. You then must removed the white wire cover (sli
... Read morece it carefully with a razor) to then see the fuse. You snip it off as you can\'t really re-use the connectors. Went to hardware store to get new connectors. Put insulated cover back over fuse and taped it in. Not the easiest repair but the unit is working good as new, and it is something I used on a regular basis.
Removed (20+) screws/safety screws, handles, then hood. Located fuse between control knob and power source held in isolator arm, then released. Stripped insulation sleeve to get to fuse and crimps. I was able to separate old crimp connectors & reuse. Not certain but, I think the fuse is directional, so pay attention when removing. Connec
... Read moreted one side of fuse then slide on heat shrink insulator, then connected the other side. I shrunk the insulation with a hair drier, then I rolled electrical tape around the fuse itself (app. 1/4\") as added insulation from external heat. I then placed the fuse back into the isolator arm, tested, them reassembled.
The thing that took the longest was making a triangle head screw driver using an old Allen wrench and grinder, as I could not find one locally. These screws can be removed with the right sized flat head but, it can be difficult and takes longer.
1. Removed Phillips head screws from entire outer casing.
2. Removed 5 screws with a triangle head drive, had to find a small, flat head screwdriver bit that fit in on an angle, a little difficult, but doable.
3. Located the in line fuse, attached to the power cord line, and covered with a heat resistant braided sleeve, and c
... Read morelamped to a metal standoff, to keep it clear from other parts.
4. Cut out original fuse which was blown (ohm meter tested).
5. Soldered in the new fuse, original was crimped in with small metal crimps.
6. Plugged in to confirm power up, digital display worked.
7. Closed the patient, resuscitation successful.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10313786
Manufacturer Part Number: GL1028
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
