Part Location Diagram of B-203-1289 Bissell Brush Roll
See part 33 in the diagram
( Grid squares measure 1x1 inch )

Brush Roll B-203-1289

Manufactured by:
Bissell
ERP Number:
ERP10270586
Part Number:
B-203-1289
Original Equipment Manufacturer ?
$15.10
Special Order

Easy 

Less than 15 mins 

(7 rated repairs) ?

Does this part fit my model?

Need help finding your model number?

Product Description

?

This is an authentic replacement part manufactured for use with bagless upright vacuums. The brush roll is used to pick up dirt by rotating bristles over the surface being vacuumed. The brush roll is sold as and individual replacement part.

Troubleshooting

This part works with the following brands:
  • Bissell
This part works with the following products:
  • Hand Vacuum
  • Upright Vacuum

Questions & Answers

?

Our customer Service team is at the ready daily to answer your part and product questions.

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Ask our Team

We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

Does this fit my product?

Customer Repair Instructions

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

Easy 

Less than 15 mins 

(7 rated repairs) ?
  • 1
Sort by:  
Sorry, we couldn't find any existing installation instruction that matched.

Belt was worn out and roller no longer turned (hair embedded in outer bearings)

Tammy from Dallas, Texas

4 of 4 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
B-32074, B-203-1289
Unscrewed roller cover, removed old roller and belt, the new ones go right back in the same way, screwed cover back on, washed the filters since I had the time, when dry put them back in
Did you find this story helpful?
Thank you for voting!

brush on vacuum was bad

Vernon from Knoxville , Tennessee

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
B-203-1289
Replaced roller brush on my vacuum cleaner
Did you find this story helpful?
Thank you for voting!

Roller bearings had frozen from wear

Glenn from TIGER, Georgia

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
B-203-1289
1. Unscrewed 4 screws holding cover
2. Removed cover and lifted end opposite belt then slid belted end out of belt.
3. Reversed procedure to install

Great fit, great part, happy wife
Did you find this story helpful?
Thank you for voting!

Belt on vacuum and roller

Donna from BEAR CREEK, North Carolina

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
B-32074, B-203-1289
1 Removed the old belt and roller
2 Put new belt on
3 Put new roller on
4 Screw the top back on
5 And done
Did you find this story helpful?
Thank you for voting!

Brush roll doesn\'t work

Hector from Riverview , Florida

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
B-203-1289
1. Remove the cover.
2. Remove the brush roll with the belt.
3. Replace the new brush roll with a new belt.
4. Replace the cover.
Did you find this story helpful?
Thank you for voting!

brush roll bearings wore out

Greg from Hamburg, New York

0 of 1 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
B-203-1289
remove 4 screws holding brush roll and belt guard in place
removed guard
pulled out brush roll
removed belt from brush roll
put new brush roll through belt
lined up the new brush roll square end tab and round end with slots and inserted brush roll into place
positioned brush roll and belt guard in place
reinserted 4 screws with screwdriver
Did you find this story helpful?
Thank you for voting!

Needed new brush roller.

Robert from Delmar, New York

0 of 1 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
B-203-1289
Just remove brush roll cover, removed old brush roll, then snapped the new brush roll in place.
Did you find this story helpful?
Thank you for voting!
  • 1