This clamshell housing set is a genuine Dewalt replacement part, not generic or aftermarket. This handle housing is a common replacement item on popular Dewalt miter saws. Both sides of the housing are included, but mounting/assembly hardware is sold separately. The on/off trigger switch is not included. This handle is a direct replacement for a broken or missing handle on your saw.rn rnThis clamshell set is compatible with the Dewalt tools listed in the 'Compatibility' section below. It will not fit any other power tools.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Worked great, perfect match.
Part fit perfectly, all screw holes lined up exactly.
Guest - April 29, 2019
Verified Purchase
★★★★★
★★★★★
Perfect fit, easy repair
Original equipment replacement part. The most difficulty was ensuring that the DeWalt tool and replacement part were compatible.
Guest - May 18, 2019
Verified Purchase
★★★★★
★★★★★
repair parts for work tools
the parts came in the time that was predicted, and i received the exact parts that i ordered. The description of the parts i needed where clear, and i appreciated how simple the ordering process was. thank you
Guest - May 27, 2019
Verified Purchase
★★★★★
★★★★★
amazed how easy it was to find the part.
perfect fit ,my saw is like new again. From fishing reels to electric tools or whatever ,if you need a part ,they will have it if it is available,will always use Ereplacement parts for my parts needs,oh yeah fast delivery too!
Frank - June 10, 2019
Verified Purchase
★★★★★
★★★★★
Clamshell Set of Saw Handles
Part was exact match to the original. It arrived in good condition.
Ken - July 16, 2019
Verified Purchase
★★★★★
★★★★★
=ƒæì
=ƒæì
Guest - August 10, 2019
Verified Purchase
★★★★★
★★★★★
The part works perfectly
Part reviews and service. Thanks for great service and and fast response time. Part was exactly the perfect fit will return when needed
Guest - August 20, 2019
Verified Purchase
★★★★★
★★★★★
Worked perfect
Worked fine. All parts were there as advertised.
Guest - September 10, 2019
Verified Purchase
★★★★★
★★★★★
This part was an exact replacement. Arrived early in great condition
Excellent service and priced competitively. Would definitely order from them again
Guest - September 28, 2019
Verified Purchase
★★★★★
★★★★★
Saw Repair
The part I ordered was the exact item I needed and I repaired my saw quickly.
Guest - November 26, 2019
Verified Purchase
< Prev
1
2
3
Next >
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Removed all bolts from existing clamshell with drill and various sizes/types of head bits.
Used phone to take snapshots of wire and trigger configuration to make it easier to reassemble properly. Removed wires from trigger switch assembly. Disconnected other wires (wrapped with wire nuts). Placed new handle bottom and fastened down
... Read more. Re-routed wires and hooked up trigger assembly. Connected other wires. Placed top of handle on and fastened bolts.
Read less
Did you find this story helpful?
Thank you for voting!
I hit my Dewalt Miter Saw Handle with a piece of lumber and the trigger handle cracked and split in half.
1. Made sure the saw was unplugged.
2. Remove screws and carrying handle from clamshell handle. Save handle and screws.
3. Remove visible screws from upper half of clamshell and remove top. Save screws.
4. It helps to take a picture of wiring configuration at trigger and inside lower half of clamshell.
5. Unscre
... Read morew trigger, remove locking washer from pivot point, remove trigger wiring from trigger and removed trigger. Save all parts.
6. Remove remaining screws from lower half of clam shell into body of saw. Remove lower half while fishing wires out of broken lower half. Save screws.
7. Fish wires through new lower 1/2 of clam shell, dry fit lower assembly with trigger and place wiring in the cradles.
8. Replaced all parts and screws following steps 1-6 in reverse order.
9. Plugged in, tested, and cut more wood! Thanks you ereplacementparts.com! You saved me $300-$400 in a new saw!!!
Remove screws to top of handle make note of wiring on inside of handle. You will need to disconnect a wire but and 4 wires hooked to the switch to get the handle off. There is also a washer like device holding the switch to the bottom of the handle you will need to reuse this metal fastener.
Once the handle is off route the wires ba
... Read moreck through the square hole in the bottom of the handle.
Wire nut the white wire and route the two blacks on one side and the yellow and red on the other. Hook them back to the switch and reattach the black plastic switch with the round metal fastener. Put the top on and screw down the yellow handle then add the black top handle with the two larger screws.
Fist make sure the Miter saw is unplugged. The remove the screws from the top carrying handle. And set the handle and screws aside. Then remove the screws from the top handle half, and remove the top handle half. Remove the cord clamp and the switch from the handle. Remove the bottom handle half from the miter saw. Install the new one. Re
... Read moreassemble everything else in reverse order.
Read less
Did you find this story helpful?
Thank you for voting!
Saw fell and cracked clamshell handle and dust duct.
Clamshell replacement:1.Unplug saw. 2.remove handle and all screws holding the clamshell body together. 3.take a photo of the switch,wire locations on the switch and wire routing 4.remove switch and remove wiring. 5.there is another screw holding the bottom of the clamshell to the saw.remove this screw and the bottom of the clamshell. rev
... Read moreerse the order to install the new clamshell.
Dust duct replacement: 1. unplug saw. 2. with the saw unlocked and in the open position, place it securely on it\'s back or side exposing the rear stationary guard. 3. remove two screws holding the guard and remove noting the position of the guard. 4. the dust duct will slide from the back of the saw forward toward the blade. 5. reverse the order to install the new dust duct. 6. rotate saw blade and test for safe clearance and movement. 7. plug in your saw and test operation.
Removed all torx screws
Disconnected all wires for the switch
Removed the broken Clamshell handle
Installed new Clamshell
Reconnected wiring to the switch
Installed torx screws
Removed the screws from the top handle, and removed the carrying handle. Took a picture of how all the parts in the lower handle were assembled and wired. Removed the cord clamp from the top handle , then removed the cord. I then removed the parts from the lower handle\' then removed the lower handle from the saw. I installed the new lowe
... Read morer handle on the saw, then replaced all of the internal parts. I then slid the new cord protector on the new cord and connected the cord. Screwed on the cord clamp. Then installed the top handle on and screwed the handles together. I then screwed the carrying handle to the top handle.
Looked at a youtube that showed each step, it it tedious as there are several layers of unscrewing to do in order, then carefully re-routing all the wires in the new arm...did work and now no problems
Did you find this story helpful?
Thank you for voting!
Saw tipped over breaking the clamshell trigger handle.
Removed top portion of the handle.
Took a picture to verify the wiring locations
Disconnected the wiring to the motor.
Removed lower portion of the handle.
Placed new lower part in place. Reconnect the wiring and put all wiring back into the slots .
Put top part of the handle on and inserted the screws.
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
3
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10170218
Manufacturer Part Number: 380452-00
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
