This item has been sourced from the original manufacturer to be used with miter saws from Makita. The slide plate connects to the base assembly. This item fits between the table and the base to provide spacing and to allow the table to pivot easily. This part is priced as a single item, please note three slide plate may be needed.
Troubleshooting
This part works with the following brands:
Makita
This part works with the following products:
Miter Saw
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(1 Review)
Click to filter by ratings:
5 stars
1
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Good experience
Parts as advertised, reasonable price and prompt service.
Guest - April 14, 2020
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
Be the first to ask our experts a question about this part!
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1. Remove the 4 bolts that secure fence to the base, remove the fence.
2. Remove kerf board.
3. Remove handle.
4. Remove Center nut and bolt that secures table to the base.
5. Remove 2 Phillips screws that secure metal spring steel clip to miter table.
6. Separate saw and table from the base.
7. Remove
... Read more damaged parts, and inspected base and miter table for cause of part failure.
8. Used 400 grit silicon carbide sanding belt remnant to smooth the surfaces that showed signs of wear, thoroughly cleaned surfaces with mineral spirits, wiped clean.
9.installed new slide plates (3) onto base, applied light coating of white grease to top side of slide plates.
10. Applied liberal amount of white grease to center hub of the miter table, set miter table onto the base, installed center bolt and nut.
11. Tightened center nut, do not over tighten, tighten the nut to the point where the table operates smoothly. Make sure that the miter table and base are firmly attached.
12. Installed new kerf boards.
13. Installed fence, make sure to square the blade to the fence.
14. Installed spring steel clip, screwed in handle.
15. Installed new carbon brush set.
16. Checked operation of tool.
Read less
Did you find this story helpful?
Thank you for voting!
Two of the slide plates were missing and the third was bent. The kerf boards were chewed up.
1. Disassembled and cleaned everything.
2. Installed the slide plates.
3. Did the necessary lubrication points.
4. Reassembled the saw.
5. Tapped in the kerf boards.
Removed the turn base and put the new plate slides in there proper place and then I put the kerf board on and that is that
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Bracket or Flange","title":"Bracket or Flange","url":"/parts/power-tool/miter-saw/brackets-and-flanges/"},{"position":2,"name":"343799-7","title":"343799-7","url":""}]
