This is an authentic Milwaukee replacement part that has been sourced from the original manufacturer to be used with cut-off/grinders. The durable handle kit includes both halves and is used to house the motor and switch assemblies. This item is available as an individual replacement part, please see illustrated diagram for associative parts.
Troubleshooting
This part works with the following brands:
Milwaukee
This part works with the following products:
Angle Grinder
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(3 Reviews)
Click to filter by ratings:
5 stars
3
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
works as expected
arrived quickly
Guest - October 25, 2019
Verified Purchase
★★★★★
★★★★★
Just what I needed
New part, fit as it should. I use this website to buy all of my replacement parts.
Guest - February 4, 2020
Verified Purchase
★★★★★
★★★★★
Fit just like the original
My grinder has had a hard life. I use it all the time. It had gotten so hot that it melted the case where the bearing for the motor is centered in the case. This fixed it in about 20 min. Just take all the screws out, swap the parts over and put the screws back in. Like new again.
Ian - September 14, 2022
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
split the case in two, removed parts from both sides, made sure that i didn\'t break any wires and put it back the same way it came apart, be careful that you don\'t pinch the wires between the case halves, the one screw that was different was a torx bit that has a hole in it, that was at the bottom of the milwaukee grinder by the battery
... Read more, that screw had a raised point in the middle, i think they call that a security screw
Read less
Did you find this story helpful?
Thank you for voting!
the rear bearing on armature overheated due to hard use and caused the plastic bearing housing/handle to melt which cause rubbing on motor internal components
removed blades, guard and handle, removed all screws on casing and grinder head (all are t20 except one h15 located on back of handle near battery attachment area) removed wire harness, switches and grinder head. Clean and inspected for wear and other damage. installed internals in new casing as they were installed in old casing, rep
... Read moreacked angle gears with fresh grease.
1, Removed gear case and handle ;by removing 9 Torx screws. The 10th screw was a security type Torx which I was forced to saw in half.
2. Removed switches and motor.
3. Soldered new brush card to switch.
4. Reinstalled brush card and switches in new handle. (The heat from the motor bearing had melted the case and allow
... Read moreed the armature to rub against the stator). Bearing inspection did not show anything wrong the bearing.
5. Reassembled with only 9 screws.
6. Enjoyed the pleasure of a successful repair.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10120601
Manufacturer Part Number: 14-34-0900
Angle Grinder
- Cordless 18 Volt 4-1/2" Cut-Off/Grinder
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_1.gif "Part Location Diagram of 14-34-0900 Milwaukee Handle Kit")
_WW_1.gif "Part Location Diagram of 14-34-0900 Milwaukee Handle Kit")
