Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
easy repair
this part was easy to install it fit perfect it took a little longer to arrive than I thought it works great
Guest - May 2, 2019
Verified Purchase
★★★★★
★★★★★
good
exact replacement, thank you
Guest - November 4, 2020
Verified Purchase
★★★★★
★★★★★
Not a good fit
The part looked to be correct However the fit was extremely tight and required a bit of sanding and a hammer to seat the plug. Once installed it worked it did the job. No more grass catching or trails if cut grass. Delivery was prompt. I would not hesitate using this supplier again.
Guest - June 6, 2019
Verified Purchase
★★★★★
★★★★★
Part was correct , thank you
I cut grass with the plug install, during the cutting cycle, grass clippings did not mulch . I had to rake entire yard to retrieve clippings.
Guest - July 26, 2020
Verified Purchase
Customer Repair Instructions
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Easy
30 - 60 mins
(8 rated repairs)?
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Lift the front of the tractor and put jacks underneath it. Remove the blade nuts from the spindle. Then remove the dull blades. Place the new blades on the spindles and tighten the blade nuts. Then I removed the old spark plug, then gapped the new one at 0.030 then installed it. I then used a nut and bolt to attach the mulch plug to the t
... Read moreractor.
Read less
Did you find this story helpful?
Thank you for voting!
Lawn mower had a rubber chute to shoot the clippings on the ground
Took off the spring loaded rubber clipping chute.
Installed the mulching black plug into the cutout where the clippings shot out.
Lined up the holes and placed a bolt, split washer and nut thru the holes. Held the plug to the mower.
15-20 minute job.
Easy to install!
Needed a mulch plug to cut up fall leaves. This is a circa 1999 MTD yard machine tractor. I have long since removed the actual chute so the thrown cuttings would spread rather than pile. The mulch plug fits into the slot nicely but the bolt hole in the plug doesn\'t line up with anything on the deck to put the bold through. So I put the p
... Read morelug in and used a small C clamp to locate where I needed to drill through the deck. put the short end of the clamp over the hole and tightened down the clamp to the top of the deck. Not too tight because the clamp begins to slip on the plastic mulch plug because it doesn\'t mount perfectly flush to the bottom of the deck so just tightened it down just short of it shifting off of the hole. Then I scratched the deck on four sides of the clamp on the top of the deck. Removed the clamp and found \"about the center of the scratch marks.\" Doesn\'t need to be absolutely exact because the mulch plug has a little give. Used a center punch to create a little dimple so the drill wouldn\'t slip. Drilled the hole, it lined up pretty good and secured with bolt, washer and thumb screw nut. I added a lock washer because things like this always tend to vibrate loose. Works great but the thumb screw loosened a bit so might use a regular nut so I can tighten down more. Made my life a lot easier because it works great and no longer have to keep going back and forth cutting the leaves smaller with each pass and not ending up with a big pile of mulch in rows. If you can use a drill, simple installation.
Read less
Did you find this story helpful?
Thank you for voting!
I wanted to install a mulch plug on a toro lx 420 riding mower
Removed bag and chute. Installed the mulch plug. It was missing a bolt and lock nut to secure to open part of deck, but I was able to find one in my inventory.
1. inserted mulch plug in place.
2. put 5/16\" bolt, 2 flat washers, 1 lock washer, and a hex nut in place.
3. Tightened said bolt and nut with ratchet / socket set.
Did you find this story helpful?
Thank you for voting!
Needed a mulch plug and new blades. I have a yardman rider and it didn\'t really fit but without any directions I made it fit.
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Deflector or Chute","title":"Deflector or Chute","url":"/parts/lawn-and-garden/lawn-tractor/deflectors-and-chutes/"},{"position":2,"name":"731-2363","title":"731-2363","url":""}]
_WW_5.gif "Part Location Diagram of 731-2363 Ryobi Lawn Mower Mulch Plug")
_WW_5.gif "Part Location Diagram of 731-2363 Ryobi Lawn Mower Mulch Plug")
