This is a genuine Kohler replacement part that has been sourced from the original manufacturer to be used with small engines. The gasket is used to seal the connection between the carburetor, insulator, and heat shield. It is recommended to replace the gaskets when servicing the engine to make proper seals and connections when the parts are reassembled. This item is available as an individual replacement part.
After years of sitting due to a bad fuel solenoid and carb, I replaced the carb assembly and studs previously removed, connected the new carb and air intake, installed choke and throttle linkages, oiled the cylinder and rotated the fly wheel by hand. Once ready, I installed a new spark plug, changed the oil and borrowed another mowers ba
... Read morettery, I fired up the scotts L1742 that has been sitting for almost 10 years! Some chugging, some smoking and oiling all the steering points a perfectly good mower with 75 hours on it is ready for service again.. why did I let it sit for so long?!
Used gaskets, fuel filter & heat shield as part of a carburetor freshen up on a MTD Yardman with Kohler 15 HP engine. Parts fit great, did have to trim the \"ears\" off the heat shield with a dremel tool to make the carburetor linkage clear...but that only took a minute & the old tractor fired right up & is running great!
I\
... Read more'll definitely use e-replacement parts again!
Read less
Did you find this story helpful?
Thank you for voting!
Bent intake valve Kohler courage sv590s 0220 engine
frank from Saint John, Indiana
1 personfound this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Removed 2-bolts from exhaust pipe, took off muffler and bracket and muffler heat guard. Valve cover, and valve head, on work bench took out retainers, caps, springs valves, push rods. Then cleaned everything.put in new valves, and replaced all parts and gaskets. Before starting project I needed to take out carburetor assembly, air filter
... Read moreassembly.make sure to gap valves. Need to torque bolts on head and valve cover. Clean off gasket glue stuck on heads,valve covers. Needed a tool to compress springs. I used vise grips. you need t-15 torx and 10mm wrench. Standard sockets, and 10mm socket. Buy a gasket kit then you have all gaskets needed for project,
Read less
Did you find this story helpful?
Thank you for voting!
Lawn tractor was hard to start and engine would knock under a load
Matt from Stanley, North Carolina
1 personfound this instruction helpful.
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
1 Removed hood
2 Removed deck and belt
3 Removed drive belt and drive pulley from engine
4 Removed battery and all wires attached to engine
5 Removed muffler
6 Removed 4 bolts holding engine on the frame
7 Removed engine
8 Removed pan off bottom of engine removed and installed a new used cam sha
... Read moreft and lifters then put engine back together with all new gaskets
Read less
Did you find this story helpful?
Thank you for voting!
Gasket were bad and leaked
Curley from Venus, Texas
1 personfound this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
1995 Toro Wheel Horse 265H lawn tractor with Kohler CV15 engine. Removed cooling shroud and covers. Removed mouse nest from around cylinder and head which is apparently what caused tractor to overheat leading to blown head gasket. Removed air breather, carburetor, valve cover and head. Inspected mechanical parts... all ok. Ordered new
... Read more gaskets from eReplacementParts.com. Parts arrived very quickly. Reassembled engine and then tractor. Runs great!
Read less
Did you find this story helpful?
Thank you for voting!
25+ year old Troy Bilt lawn tractor with Kohler engine. Throttle shaft seal worn off, linkage tab broken off, & throttle shaft was so worn that it was surrounded with brass dust. It would no longer
1. Removed air cleaner.
2. Removed air cleaner box from the carb.
3. Removed choke & throttle linkages from choke & throttle
4. Removed carb body. This took a little tugging, twisting because the gasket was stuck to both the carb body & intake port. Scraped old gasket of both surfaces.
5. Removed butterfly from
... Read morethrottle shaft.
6. Replaced throttle shaft & seal; reinstalled butterfly on shaft.
7. Installed new gasket. I like to use a thin film of grease on gaskets but maybe that\'s just me.
8. Repeated steps 4-3-2-1 using \"replace\" instead of \"removed\".
I thought my chances of getting replacement parts for an engine this old were about zero. Thanks to eReplacementParts, this old Kohler is running like a top! (It helps, too, that it\'s a Kohler.)
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP9883867
Manufacturer Part Number: 1204101-S
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Seal or Gasket","title":"Seal or Gasket","url":"/parts/lawn-and-garden/engine/seals-and-gaskets/"},{"position":2,"name":"1204101-S","title":"1204101-S","url":""}]
(2007)_WW_12.gif "Part Location Diagram of 1204101-S Kohler Gasket: Carburetor")
(2007)_WW_12.gif "Part Location Diagram of 1204101-S Kohler Gasket: Carburetor")
