Part Location Diagram of 16220-ZE1-020 Honda Carburetor Spacer
See part A-2 in the diagram
( Grid squares measure 1x1 inch )

Carburetor Spacer 16220-ZE1-020

Manufactured by:
Honda
ERP Number:
ERP9899093
Part Number:
16220-ZE1-020
Original Equipment Manufacturer ?
In Stock
Delivers in 3-5 Business Days!

Easy 

30 - 60 mins 

(5 rated repairs) ?

Does this part fit my model?

Need help finding your model number?

Product Description

?

This part is a genuine OEM item that has been sourced to be used with Honda small engines. This spacer is used as a link between the carburetor and the air cleaner elbow. The carburetor spacer is priced as an individual part, please note associative parts are available separately.

Frequently Purchased Together

?

Troubleshooting

This part works with the following brands:
  • Honda
This part works with the following products:
  • Engine
  • Lawn Mower
  • Snow Blower
  • Water Pump
  • Tiller
  • Generator
Part# 16220-ZE1-020 replaces these:
16220-ZE1-000,

Customer Part Reviews

?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(4 Reviews)
Click to filter by ratings:
  • 5 stars
    4
  • 4 stars
    0
  • 3 stars
    0
  • 2 stars
    0
  • 1 star
    0
  • 1
Sort by:  
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.

Questions & Answers

?

Our customer Service team is at the ready daily to answer your part and product questions.

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Ask our Team

We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

Does this fit my product?

Customer Repair Instructions

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

Easy 

30 - 60 mins 

(5 rated repairs) ?
  • 1
Sort by:  
Sorry, we couldn't find any existing installation instruction that matched.

Honda EU3000is would only run with the choke on

Raymond from HOT SPRINGS, North Carolina

4 of 4 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set, Wrench set
Removed and replaced carburetor. This particular generator needs to be run at least once a month and run on top tiered fuel only or you will be buying many carburetors.
Did you find this story helpful?
Thank you for voting!

Carburetor clogged up

tom from selma, Alabama

2 of 2 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Unbolt old carb, remove linkage and fuel line , then reverse procedure.
Total time 15 minutes!
Parts arrived quickly via priority mail!!
Definitely recommend !
Did you find this story helpful?
Thank you for voting!

I had purchased a new carburetor but discovered the gaskets were too bad to reuse.

LESLIE from Madison Heights, Virginia

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Installed the new gasket and spacer along with the new carburetor. It fired up on the 2nd pull.
Did you find this story helpful?
Thank you for voting!

Gas deposit buildup around shaft and in carburetor bowl, causing motor to run wide open.

Billy from Cedar Hill, Tennessee

1 person found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
1. Had to remove the pump from the frame. Carburetor could not be removed from motor without hitting the frame.
2. Carburetor was removed and taken apart. throttle was sticking in the open position due to gas deposit build up on the shaft.
3. Soaked the carburetor in cleaner for thirty minutes and put back together, re-inst alled on motor.
4. Motor started up fine and idle like it should.
The new blend of gas is really hard on small engine because of deposit from the gasoline. In my case the large pump is only used once or twice a year and just set in the shop on a shelf. It \'s eight year old and looks new. Honda makes a very good motor, not a design problem, it a !!GAS!! problem.
Did you find this story helpful?
Thank you for voting!

Restoring an old motor

Bob from Monticello , Indiana

0 of 1 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Removed carb thoroughly a reassembled
Did you find this story helpful?
Thank you for voting!
  • 1