This is a manufacturer approved replacement part used on lawn and garden equipment. The push rod rides on the camshaft to push the exhaust valve open during the exhaust stroke. A bent push rod can not only affect your engine's performance, it can seriously damage other parts if the problem is not taken care of immediately. This part is made out of metal and it is sold individually.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Lawn Mower parts
The parts were in good condition and just exactly what I ordered. Lawn Mower is now running perfect again.
Guest - September 13, 2019
Verified Purchase
★★★★★
★★★★★
As expected
Original replacement parts make repairs so much easier. Thank you
ereplacementParts.
Stephen - September 26, 2019
Verified Purchase
★★★★★
★★★★★
right part perfect
arrived good condition packaged well
Guest - May 6, 2020
Verified Purchase
★★★★★
★★★★★
Eady Easy repair great parts
Parts worked great im very pleased with every purchase with replacement parts.
Fernando - October 15, 2020
Verified Purchase
★★★★★
★★★★★
parts worked as they should
yhe pushrods & gasket arrived quickly & in perfect shape , finished the project and the tractor is ready to push more snow.
Gerald - February 20, 2021
Verified Purchase
★★★★★
★★★★★
Received parts in disarray.
It appears all the parts ordered are the correct ones. As soon as the weather warms, I'll know when I begin the remantling process. One negative. The small box with parts was open and smashed with parts strewn throughout from mishandling during shipment. The smaller rocker caps could have made it outside the box as there were cardboard breaks in the corners. Make sure packagers put some foam or bubble wrap to protect the integrity of the contents.
Guest - April 29, 2023
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
Be the first to ask our experts a question about this part!
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
We removed the engine from tractor. Removed pan from engine to inspect cam shaft. The compression was ok reinstall. Remove and replace oil seal Remove old pan gasket and replace pan gasket and reinstalled. Taking care to install oil seal on shaft. Remove valve cover and remove and replace both push rods. Reassemble and install back on tr
... Read moreactor. Start and check for leaks and operation. Have 28years in small engine repair
Removed valve cover
Loosened valve rocker enough to rotate away
Remove push rod
Replace cap on valve
Put rocker back into place and adjust to motor specs
For my motor valve adjustment was
.003-.005 for intake
.005-.007 for exhaust
1. Remove last part of the push rod and checked the valve tappet for defects, cleaned old head gasket off and installed the new gasket
2. Set the exhaust and intake valves push rods in place
3. Adjusted the valve clearances to B&S spec\'s
4. Installed new valve gasket after cleaning off the old valve cover gasket
5
... Read more. Started the engine with success
Read less
Did you find this story helpful?
Thank you for voting!
The engine would blow gas out the carburetor and the lock up, took off the valve cover and found the exhaust rocker arm split and intake push rod bent.
I replaced both rocker arms and intake and exhaust push rods. Adjusted the gap. I started the engine, it fired and I let it idle for a few minutes. The engine never sputtered or skip a beat. I mowed for two hours in the 8-inch high grass the riding mower pushed thru.
Thank you for your service, I will remember your company fo
... Read morer future service.
1. Remove the valve cover.
2. Loosen intake lifter and remove push rod.
3. Replace with new intake push rod.
3. Loosen exhaust lifter and remove push rod.
4. Install new exhaust push rod.
5. Install new valve cover gasket.
6. Install valve cover.
Replaced piston rings, replaced push rods and guide, cleaned and lapped valves, adjusted valves, and replaced carburetor. I did not put enough torque on the flywheel bolt and sheared off 2 keys before looking for information online and most information said to torque bolt to 120 ft. lbs. and then go a little further. Did this, problem was
... Read more solved, and engine runs great.
Read less
Did you find this story helpful?
Thank you for voting!
The engine engine bent the intake push rod . did not know why.
richard from Hop Bottom, Pennsylvania
0 of 1 peoplefound this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
disassemble the cooling shields remove the carb. and the muffler .
pulled the head off to see what was in the engine to bent the rod .
seen nothing to bent the rod cleaned off the carbon from the piston .
clean surfaces and re assemble the engine .
working perfectly now .
Did you find this story helpful?
Thank you for voting!
Rocker arm retaining nut broke,allowing the push rod to bend.
Lawn Mower
- Cub Cadet Lawn Mower Model 17BA5A4G710 Parts
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
