Genuine OEM replacement Grommet used on Lawn and Garden equipment Engines. This Rubber breather grommet is used as a seal between Breather Assembly and the Breather Tube. Over time rubber grommet may dry out and crack so it should be replaced.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
right part
arrived on time good shape.
Guest - October 9, 2019
Verified Purchase
★★★★★
★★★★★
Breather elbow
Fit perfectly
Guest - December 3, 2019
Verified Purchase
★★★★★
★★★★★
Perfect Part
Arrived quickly and fixed my problem
Guest - April 6, 2020
Verified Purchase
★★★★★
★★★★★
Old tiller repair
I found the parts I needed to repair my old tiller that I bought used more than 30 years ago. The 4 HP original engine had been replaced with a 5 HP Briggs so no other site I found could identify the parts I needed, not even Briggs. Using parts breakdown from the ereplacement site I found exactly what I required. Everything fit and was exactly as described. Now ready for spring gardening.
Scott - April 18, 2020
Verified Purchase
★★★★★
★★★★★
Tiller
Part fit great, all good, tiller Briggs ran good!
Guest - April 22, 2020
Verified Purchase
★★★★★
★★★★★
Breather tube grommet for my tiller
The part was easy to find on the site. It shipped quickly, arrived in a timely manner and was reasonably priced.
Guest - June 19, 2022
Verified Purchase
★★★★★
★★★★★
Econo shipping order lost again
Once again, my order was lost in transit! This is the second time in a couple of months that this has happened! I'm now 2 weeks behind a rebuilt that needed to be completed 2 weeks ago.
I called your 877 number & they have refunded my purchase ,that's all well & fine but now the process starts all over again & my rebuild is incomplete! It appears that the postal service AKA the econo ship has failed yet once again.
Lonnie - August 16, 2019
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
Be the first to ask our experts a question about this part!
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Remove the breather tube, and both grommets from the breather assembly. Remove the old grommets and installed the new grommets. Remove the air cleaner cover and remove the old pre filter and install the new on, then place the cover back on.
Did you find this story helpful?
Thank you for voting!
Bad Carb,bad plug and changed oil and air filter.
Bobby from Carlisle, Ohio
4 of 4 peoplefound this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
I removed the lever panel, gas tank, and carborater in that order. I cut a new gasket for the carb to rest on, flushed the carb with cleaner, flushed the gas tank with fresh gas, replaced the diaphram, and reassembled. Finally adding the air filter and replacing the cap. She cranked up after ten pulls. The grommets had weathered and neede
... Read mored replacing. Other than that, it was pretty straight forward.
Read less
Did you find this story helpful?
Thank you for voting!
Motor had set up for several years. Gaskets and grommets were bad.
Ordered carburetor for a 25 yo Pollen Garden teller w/Brigs 5 hp engine. Two screw holes had to be opened up with tap. Ordered later two grommets that were needed to replace the old parts. Most difficult to replace this carb. on this engine. When done Just two pulls and purring like a kitten. Good carb.
Too off air breather to get to carb. Unbolted gas tank and carb. Used tools to take apart carb. Scraped old gaskets off carb. Used carb cleaner spray and compressed air to spray our all holes and cleaned carb. Put new gaskets on then fired right up. Will deff use in the future for parts etc.
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
(1979)_WW_4.gif "Part Location Diagram of 692187 Briggs and Stratton Grommet")
(1979)_WW_4.gif "Part Location Diagram of 692187 Briggs and Stratton Grommet")
