This component is supplied by the original equipment manufacturer for DeLonghi coffee makers. It is an important part of the boiler mechanism. Unfortunately, over time valves tend to wear out and they may begin to fail eventually requiring a replacement. Check the diagrams for your model to ensure the proper repair procedure. You may need a screwdriver to replace this component. Keep in mind it is made of durable material and is sold as an individual item.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
simple easy repair of espresso machine.
The part was genuine and fit perfectly!
Guest - July 9, 2020
Verified Purchase
★★★★★
★★★★★
Saved hundreds
an easy repair of a simple part saved hundreds. Too many people throw away and buy new for hundred or more when a 5 dollar part and a couple of screw turns can fix the problem. Thank you for having the right parts.
Guest - August 10, 2020
Verified Purchase
★★★★★
★★★★★
Espresso machine like new again!
Arrived on time, part worked perfectly. Espresso machine like new again!
Iglobal - July 12, 2022
Verified Purchase
★★★★★
★★★★★
Replacement parts
Fast shipping and good com.unication. Parts fit as described. Thank you.
Guest - November 12, 2022
Verified Purchase
★★★★★
★★★★★
Perfect
Great experience
Guest - December 27, 2022
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Using a Phillips screwdriver, remove the screw in the center of the diffuser and remove the diffuser. Using a regular screwdriver, remove the dowel. It may be really tight but should just unscrew. Remove and replace the valve and valve spring sitting on top of the dowel. Replace the dowel and diffuser. It may be necessary to remove the bo
... Read morettom for easier access.
The hardest part was reaching three screws which secure the top of the machine. It requires a star drive. All of the other screws are small Phillips heads. After you remove those and two on the back, the top will lift right off.
I promise, everything is very intuitive. Unplug the hoses by simply pulling on them, remove the pu
... Read moremp by wiggling it off its rubber mounts and unscrew the water valve connected to the pump the pump. Replace those with the new ones and reverse the process.
I chose to change a few of the other little pieces of tubing, simply because I was under the covers - super simple and cheap.
I also replaced the spring and valve on the head (where the water comes out) to ensure that the new pump didn\'t overwhelm an old valve.
This pump works perfectly in our Delonghi EC702, it actually is an improvement over the original one. With these parts changed, we have a completely new machine!
Thanks eReplacement for the super fast service and clear parts catalog!
Read less
Did you find this story helpful?
Thank you for voting!
DeLonghi Expresso Maker was leaking steam and water. The frothing wand stopped working.
1. Removed water reservoir.
2. Unplugged unit.
3. Turned upside down on a table.
4. Unscrewed and removed silver diffuser plate.
5. Next, unscrewed a large headed screw with a flat head screw driver. This screw has a hole in the center. This screw holds the valve spring, valve ring and valve in place.
6. Afte
... Read morer removing this large headed screw, I removed the \"old\" valve spring, valve ring and valve assembly.
7.On the small end of the new valve spring I inserted the new valve ring. I then inserted the new valve into the valve ring. NOTE that the valve is made of silicon rubber. After inserting the valve, the rounded head is on top of the valve ring.
8. I inserted the completed assembly from 7. into the chamber or slot.
9. I screwed the large headed screw back in place.
10. I screwed the silver diffuser plate back in place.
11. I attached the water reservoir and filled with water.
12. I plugged the unit back in and turned it on.
13. NO MORE leaking water or steam, and the frothing wand was functional once more.
Read less
Did you find this story helpful?
Thank you for voting!
The machine\'s lower-boiler output valve was leaking before running a cycle due to the lower boiler being broken and the valve spring missing.
1.) Used a 3mm flathead bit on a long, but skinny screwdriver to unscrew the top heating base from the machine via the black base that surrounds where the water outputs.
2.) Used a Phillips Head #0 bit to remove the two small screws on the back of the machine connected to the top heating base.
3.) Removed the top heating base.
... Read more 4.) [CAUTION]If there\'s water still in the boiler, it will leak. If the boiler is hot, steam may exit, so let the machine cool down before continuing this step[CAUTION] Used an H3.5 (Hex) bit to remove the lower boiler from the upper boiler. It may also help to unplug the connectors from the upper-boiler for easier removal. Take a picture as you go to make it easier to put the wires back in the right places.
5.) After removing the upper boiler, remove the lower boiler.
6.) Grab the new boiler and put together the spring valve contraption. Place the valve ring inside the smaller end of the spring, then the valve, and carefully place the spring into where the dowel would go, with the valve going in first.
7.) Then screw in the dowel.
8.) Place the repaired or newly put together lower boiler back into its position.
9.) Screw the top boiler back to the bottom boiler with the H3.5 (Hex) bit. If you removed the wires, place them back in their respectful positions.
10.) Re-attach the top heating base.
11.) Screw the two small screws back into the back of the heating base with the PH#0 bit.
12.) Screw the three screws that connect the black base to the heating base with a 3mm flathead.
Read less
Did you find this story helpful?
Thank you for voting!
Valve deteriorated allowing water leaks on pressure side of the pump. Check valve on boiler outlet leaked.
Replaced valve on outlet side of pump usine screw driver to gain access and needle nose pliers to remove spring clips on water lines.
Removed check valve with blade screw driver, cleaned valve seat with fine grit piece of sand paper and installed new valve.
Did you find this story helpful?
Thank you for voting!
Espresso machine needed a new ball valve on the boiler outlet.
My DeLonghi espresso machine was leaking 2/3rds cup of water about 15 seconds after turning off the pump, and the steam wand was operating poorly. I determined the boiler ball valve had broken into bits and was no longer functioning. I decided to replace the valve ring and valve spring at the same time.
Make sure the machine is
... Read morenot hot before starting.
1) With a Phillips head screwdriver, remove the screw in the center of the diffuser and remove the diffuser.
2) Using a flathead screwdriver, remove the dowel.
3) Remove what\'s left of the valve, valve spring, and valve ring.
4) Thoroughly clean the dowel and diffuser.
5) Turn machine upside down and replace the valve ring, valve, and valve spring, being careful to seat the valve correctly.
6) Replace the dowel by screwing it down with a flathead screwdriver. Screw in until just tight and then back off about a 1/4 to a 1/2 a turn.
7) Replace the diffuser using the Philips head screwdriver.
In addition I needed to descale my machine before it began operating as expected. My machine had sat empty and idle for several months and I believe this contributed to the degradation of my ball valve.
Read less
Did you find this story helpful?
Thank you for voting!
Very dim OK light, dripping from espresso outlet during milk steaming
1. Removed the top and bottom (philips screws on top and bottom of base, philips screws and torx screws from beneath upper section, small philips screws at top of back face) to access internals.
2. Slid cover plate over front buttons lights outward (sort of unhooks)
3. Clipped wires to green \"OK\" light, removed light from so
... Read morecket (old light was small light inside a cover; replacement had bulb shaped like cover so one piece). Soldered new light to clipped wires, covered with shrink wrap slid on before soldering. Note that there\'s a resistor inline with the new light, and probably under all the shrink wrap on the original. Make sure you don\'t trim that off when shortening the new light\'s leads if doing so. Note! Same as for one other person whose review I read, the replacement light labeled as green was actually orange. Whatever the cause, it\'s next to the OK label and much easier to see! The green was super-dim...
4. Turn machine onto its back and use philips screwdriver to remove espresso brew screen screw and pop screen off (it may stick to the rubber behind a bit).
5. Use flat blade screwdriver to remove the now-visible center fastener.
6. Extract the spring and valve. I was unable to remove the \"valve ring\" easily, and decided that replacing the old valve was probably adequate, and this appears to be true so far. The ring is brass or something, the valve is a plastic or rubber or similar which appears to have hardened over time.
7. Assembly is the reverse of disassembly (haha). But it really is, just using the new spring and valve.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
