Black and Decker Screwdriver Parts
We sell only genuine OEM Black and Decker ® parts.
Top Black and Decker Screwdriver Models
-
Black and Decker BDCS50C (Type 2) 4V Storage Screwdrvr Power Tool Screwdriver Parts
-
Black and Decker BDCSFL20C (Type 2) Cordless Screwdriver Parts
-
Black and Decker PD600G (Type 1) 6V Screwdriver Power Tool Parts
-
Black and Decker PP360-AR (Type 1) 4.8V Screwdriver Parts
-
Black and Decker BDSG500-B2 (Type 1) 4.5A Drywall Screwdriver Parts
-
Black and Decker LI3000P (Type 1) Compact Lilon Screwdriver Parts
-
Black and Decker BDCS36F-AR (Type 1) 3.6V Li-Lon Screwdriver W Parts
-
Black and Decker 9072 (Type 4) 2.4V Screwdriver Parts
Popular Black and Decker Screwdriver Parts
- Manufacturer Part Number:
- 96558-00
This is the clutch • for various models of screw guns and drywall screwdrivers. Screw guns, not to be confused with power drills, feature a nose instead of a chuck and the clutch within is responsible for engaging or disengaging the motor of the screw gun to stop it from overdriving the screw. This OEM clutch is made of durable metal, has a 1-inch diameter and includes only a single retaining ring...
- Manufacturer Part Number:
- N559955
- Manufacturer Part Number:
- 176846-04
This carbon brush is an authentic DeWalt replacement part. It is sold individually, 2 are needed to make a set • Worn brushes are frequently the cause of a poorly running motor. • Replacing brushes can fix an intermittently operating motor. • New brushes can restore a motor's electric braking. Carbon motor brushes are one of the most commonly replaced power tool parts. The reason is that c...
- Manufacturer Part Number:
- 605040-20
This Ball Bearing has metal shielding on both sides. This is a genuine Dewalt replacement part that is sold individually. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. • Bear...
- Manufacturer Part Number:
- 143079-00
- Manufacturer Part Number:
- 96558-04
It is a genuine item that is supplied by the original manufacturer for use with DeWALT and Black and Decker power tools. This clutch is a special component that helps to engage the drive shaft. It provides an identical replacement for a damaged or a missing hardware that was installed on a new unit. Check the diagrams for your model for the exact location and the correct installation of this part....
- Manufacturer Part Number:
- 607904-22
It is a genuine item that is supplied directly from the original equipment manufacturer for use with Black and Decker and DeWALT screwdrivers. This is an identical replacement for a faulty or a damaged component that was included with a new unit. Press the release buttons and remove the collar from the clutch housing. Use pliers to remove the worn bit and install the new bit tip. Note, this high-q...
- Manufacturer Part Number:
- 093128-00
Included in part number 611971-00
- Manufacturer Part Number:
- 90593304
This is a Genuine Manufacturer Approved replacement part used on some Black and Decker Power Tools. This item is sold individually. Chargers will wear out overtime. Purchasing a charger will be less expensive than buying a new vacuum. Please note that a weak or defective battery can damage the charger. Weak batteries are batteries with bad cells. These type of batteries will not hold a charge. It ...
- Manufacturer Part Number:
- 696631-00
Genuine Dewalt replacement part, this item is sold individually. The 696631-00 Steel Ball is part of the chuck assembly of the Impact Drivers shown below. When you pull back the sleeve of the chuck assembly and insert your bit, the Steel Ball is the part that locks the bit in the chuck assembly. In the Screw Drivers listed below this is the part that secures the Bit Holder in the spindle.
- Manufacturer Part Number:
- 90593303-01
This is a genuine Black and Decker replacement charger, sold individually. It’s designed to recharge the battery used in the cordless tools listed below. Over time, chargers can wear out or stop functioning properly. Replacing the charger is a cost-effective solution that can extend the life of your tools—often much less expensive than purchasing a brand-new unit.
- Manufacturer Part Number:
- 094518-00
This retainer, also known as a retaining ring or split ring, is a genuine OEM replacement part used in cordless drills. It is responsible for securing the spindle within the clutch housing so that it remains stable during use and ensuring the components such as gears and bearings do not slide off the spindle. Over time the retainer may crack, corrode, or fall off, leading to wobbly parts and exces...
Black and Decker Screwdriver Models
-
Black and Decker BDCS50C (Type 2) 4V Storage Screwdrvr Power Tool Screwdriver
-
Black and Decker BDCSFL20C (Type 2) Cordless Screwdriver
-
Black and Decker PD600G (Type 1) 6V Screwdriver Power Tool
-
Black and Decker PP360-AR (Type 1) 4.8V Screwdriver
-
Black and Decker BDSG500-B2 (Type 1) 4.5A Drywall Screwdriver
-
Black and Decker LI3000P (Type 1) Compact Lilon Screwdriver
-
Black and Decker BDCS36F-AR (Type 1) 3.6V Li-Lon Screwdriver W
-
Black and Decker 9072 (Type 4) 2.4V Screwdriver
-
Black and Decker BDCS40BI (Type 1) Pivot Scrdrvr W/Batt Screwdriver
-
Black and Decker 2121R (Type ALL) Drywall Scrugun Screwdriver
-
Black and Decker LI2000 (Type 2) Pivot Driver Power Tool Screwdriver
-
Black and Decker LI2000 (Type 1) Pivot Driver Power Tool Screwdriver
-
Black and Decker BDSG500-BR (Type 1) 4.5A Drywall Screwdriver
-
Black and Decker 2145-SBD (Type 100) Versa-Clutch Scrugun Screwdriver
-
Black and Decker BDCS36F-BR (Type 1) 3.6V Li-Lon Screwdriver W
-
Black and Decker BDCS36F-B3 (Type 1) 3.6V Li-Lon Screwdriver W
-
Black and Decker 9019-35 (2) 3.6V Screwdriver - Mexico
-
Black and Decker BDSG500-AR (Type 1) 4.5A Drywall Screwdriver
-
Black and Decker BDCS80I (Type 1) 8V Screwdriver
-
Black and Decker 2038-220 (Type 101) 220V 2500 Rpm Dw Scrugun Screwdriver