OEM Delta Scroll Saw Parts & Accessories

Clamp Knob Assembly – Part Number: 286303-00

$24.56

Manufacturer Part Number:: 286303-00

This is a genuine OEM sourced replacement part designed for use with Dewalt and Delta saws. The purpose of this part is to tighten the blade clamp assembly. It is made out of metal with plastic and it is sold individually.

Blade Chuck

★★★★★

(14)

$28.20

Manufacturer Part Number:: 5140099-98

Genuine Dewalt replacement part, this item is sold individually. This is a part of the blade holding assembly on the Scroll Saws listed below.>br>Along with the other parts shown in the parts diagram this will clamp the scroll saw blade and hold it in place.

Brush

★★★★★

(5)

$10.63

Manufacturer Part Number:: 286346-00

Genuine DeWalt replacement part Includes 1 Carbon Brush with wire lead and brush spring attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear items, m...

Short Sleeve

$10.67

Manufacturer Part Number:: 286294-00

The short sleeve helps to distribute pressure evenly between connected components. Over time it will wear out, get damaged or lost eventually requiring a replacement. This authentic manufacturer-sourced part is specially designed for use with DeWALT and Delta scroll saws. Check the diagrams for your model for the exact location and the correct application of this hardware. Keep in mind this high-q...

Foot

★★★★★

(4)

$14.98

Manufacturer Part Number:: 286292-00

This part is guaranteed OEM, made to fit the DeWALT and Delta scroll saws listed below. This hold down foot is attached to the top mount via the black bar. Note that mounting/adjustment screw is sold separately. This foot is sold individually. Associated parts: • Top Mount, part # 286277-00 • Bar, part # 286291-00 • Screw, part # 286316-00

Switch

★★★★★

(11)

$38.42

Manufacturer Part Number:: 5140092-86

This is an OEM replacement part used in Delta and DeWALT scroll saws. It is an on/off switch and is sold individually, separate from the speed control knob. It is plastic with metal terminals. Over time, mechanical parts such as these wear down and must be replaced. To complete this repair you will need a hex key/allen wrench. • Remove old switch by pressing tabs • Disconnect wires • Atta...

Air Nozzle

★★★★★

(9)

$25.16

Manufacturer Part Number:: 286311-00

This is an authentic OEM replacement part, guaranteed to fit the scroll saws listed below. This adjustable air nozzle/hose is used as a dust blower. It is connected to the bellows via the metal air pump cap. Nozzle attaches over the air pump cap's ball end. When installing this part it is recommended to heat the nozzle's connecting end until soft. Then just ease into place. This item is sold indiv...

Bellows

★★★★★

(1)

$5.95

Minimum Quantity of 2 required

Manufacturer Part Number:: 286289-00

This is an authentic replacement part, sourced from the original manufacturer for use with scroll saws. The special rubber bellow is used to push air through the air pump and through the air nozzle. This bellow is available as an individual replacement part, please see model diagram for associative parts.

Table Insert

★★★★★

(7)

$5.95

Manufacturer Part Number:: 900200

This replacement table insert is specially designed for Delta scroll saws. It is a genuine part that is supplied from original equipment manufacturer. The purpose of an insert is to reduce the splintering and chips on the cuts. It also helps to prevent thin slices of wood from jamming in between the blade and the plate. This item is made out of plastic and it is sold individually. To replace this ...

Bar

$16.63

Manufacturer Part Number:: 286291-00

This is a genuine OEM sourced replacement part that is intended to be used with scroll saws from DeWalt and Delta. The metal bar attaches to the top rocker mount and is used to support the foot that protects the blade. The bar will require a torx driver and hex driver to install, and the bar is priced as a single item.

Fuse,3a

★★★★★

(4)

$11.48

Manufacturer Part Number:: 286344-00

This fuse is a high quality part sourced from the original manufacturer for DeWalt and Delta scroll saws. The fuse is a safety feature to prevent an electric surge from overloading the motor. Once the fuse is tripped it will burn itself out, and will need to be replaced. This part is sold individually, keep in mind the fuse cap is sold separately.

Band Saw Table Insert

★★★★★

(14)

$13.20

Manufacturer Part Number:: 426020630001S

This is a table insert plate for your saw. It is attached to the table, and provides access to the blade. A table insert protects the rest of the unit by preventing wood from getting jammed under the blade during cutting. The slit in the insert plate allows for the saw blade to run smoothly. Before installing this part, unplug your saw.

Delta Scroll Saw Parts

Top Delta Scroll Saw Models

Popular Delta Scroll Saw Parts

Delta Scroll Saw Models

Delta Scroll Saw Parts

Search By Model or Part Number

Top Delta Scroll Saw Models

Popular Delta Scroll Saw Parts

Delta Scroll Saw Models