OEM Milwaukee Sander Polisher Parts & Accessories

Ring Retaining 0.8mm Thk – Part Number: 44-86-1380

$5.95

Minimum Quantity of 2 required

Manufacturer Part Number:: 44-86-1380

This is an authentic OEM part which is designed for use with Milwaukee tools. It is a special hardware which helps to secure components. This is an identical replacement for a damaged or a faulty part that was installed on a new unit. Check the appropriate diagrams for your model for the exact location and the correct installation of this retaining ring. You will need snap-ring pliers to remove th...

Hook And Loop Sander Pad

★★★★★

(48)

$10.08

Manufacturer Part Number:: 51-36-7100

Genuine Milwaukee replacement part. Includes one Pad. This Pad is used to hold 5 inch Hook and Loop sandpaper with 8 vacuum holes. Over the past few years the popularity of Hook and Loop paper has grown because of the ease of changing sandpaper when needed. Over that of the PSA (Pressure Sensitive Sandpaper) Applying too much pressure on the sander may cause premature wear on the Hook and Loop...

Carbon Brush

★★★★★

(8)

$8.17

Manufacturer Part Number:: 22-18-0710

Genuine Milwaukee replacement part Includes 1 carbon brush with wire lead attached, Sold individually • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear ...

Brush Cap

★★★★★

(2)

$5.98

Manufacturer Part Number:: 23-44-0210

This is a genuine Milwaukee replacement part, it is sold individually. This Brush Retaining Screw (Brush Cap) is used on the model numbers shown below. The purpose of this part is to secure the brushes in the brush holder To remove this part ,simply use a flat head screw driver. Don't use too much pressure on it, they do have a tendency to break.

Carbon Brush

★★★★★

(6)

$24.87

Manufacturer Part Number:: 22-18-0730

Genuine Milwaukee replacement part. Includes 1 Carbon Brush with wire lead and brush spring attached. 2 of these brushes are need for the tools listed below. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power t...

Brush Holder Assembly

$6.88

Manufacturer Part Number:: 22-22-1325

This is an authentic manufacturer sourced replacement assembly designed for use with Milwaukee power tools. This part holds carbon brush around the armature to provide stable and safe contact. It is made out of plastic with metal and it is sold individually. Please note carbon brushes are sold separately. To replace this assembly you would need a screwdriver and pliers. • First remove screws h...

Ball Bearing

★★★★★

(1)

$9.42

Manufacturer Part Number:: 02-04-1229

This authentic replacement part is designed for use with Milwaukee drills/drivers. Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. Bearings experience constant wear from pressure, heat, vibration and friction. Because of this, many bearings need...

Cord Set

★★★★★

(5)

$17.57

Manufacturer Part Number:: 22-64-0215

This cord is an authentic Milwaukee replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. rnPower Cord Specifications: rn • 2 Prongs rn • 2 Wires rn • 18 Gauge rn • 8 Feet Long

Ball Bearing

★★★★★

(1)

$7.08

Manufacturer Part Number:: 02-04-0910

This is an authentic part produced by the original manufacturer. It is compatible with Milwaukee power tools including grinders, sanders, and polishers. Ball bearings secure moving parts, allowing for free movement while reducing friction. They are high wear parts that may need regular replacement for optimal performance from tools. Sold individually.

Ball Bearing

★★★★★

(1)

$10.70

Manufacturer Part Number:: 02-04-0845

This is a Genuine OEM Approved replacement part used on a variety of Milwaukee Power Tools. This Ball Bearing has multiple applications based on your tool. Ball Bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows ...

Carbon Brush

★★★★★

(4)

$17.22

Manufacturer Part Number:: 22-18-0126

This Genuine OEM Milwaukee Carbon replacement part is Sold Individually. Due to continuous contact with Armature carbon brushes need to be inspected periodically and need to be replaced if they are worn. Carbon motor brushes are one of the most commonly replaced power tool parts. Please Note: Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced ...

Carbon Brush Assembly

★★★★★

(9)

$5.95

Manufacturer Part Number:: 22-18-0680

Genuine Milwaukee replacement part. Includes 1 Carbon Brush with wire lead, brush spring and bracket attached. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that's operating intermittently. • New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is bec...

Milwaukee Sander Polisher Parts

Top Milwaukee Sander Polisher Models

Popular Milwaukee Sander Polisher Parts

Milwaukee Sander Polisher Models

Shop by Popular Milwaukee Sander Polisher Part Types

Milwaukee Sander Polisher Parts

Search By Model or Part Number

Top Milwaukee Sander Polisher Models

Popular Milwaukee Sander Polisher Parts

Milwaukee Sander Polisher Models

Shop by Popular Milwaukee Sander Polisher Part Types