We Sell Only Genuine Makita® Parts.
Makita Hedge Trimmer Parts & Models
Popular Makita Hedge Trimmer Parts
This pan head screw is a genuine replacement hardware sourced directly from original equipment manufacturer. It is specially produced for use with a variety of power tools. Please make sure to check appropriate diagrams for your tool to ensure the correct location and applications of this hardware. Includes one (1) metal screw and a washer.
Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.
Genuine Makita replacement part, this item is sold individually.
This Retaining Ring is used in a number of Makita Tools as shown below.
Retaining rings are used in various parts of tools.
They are usually installed on a shaft to keep a bearing or a gear from moving.
They are also used in other applications depending on what tool you are working on.
This is an example of an external retaining ring.
• This cord guard is a genuine Makita replacement part and is sold individually.
• Cord guards, also called cord protectors, are designed to slide onto your cord and fit securely at the end, where it’s firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.
• This cord guard will fit cords for the tools listed under the “Compatible Tools” listing. It is not guaranteed to fit any other cords.
This is an authentic manufacturer approved replacement part designed for use with Makita gas trimmers and blowers. It is designed to keep fuel in the tank. This fuel cap is made out of plastic and it is sold individually. Please note the gas cap retainer is sold separately.
This is an OEM approved replacement part. It is specially designed for Makita gas trimmers/edgers. Its purpose is to filter out dust and debris from contaminating the carburetor and engine. Over time this filter will get clogged and worn no longer performing as intended. This filter is made out of foam and it is sold individually.
To replace this filter a screwdriver is needed.
• Remove the cover screw
• Remove the cover
• Replace the filter element
• Reassemble and test the unit
This pan head screw is a genuine replacement hardware sourced directly from original equipment manufacturer. It is specially produced for use with a variety of power tools. Please make sure to check appropriate diagrams for your tool to ensure the correct location and applications of this hardware. Includes one (1) metal screw and a washer.
Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.
Genuine Makita replacement part, this item is sold individually.
This Retaining Ring is used in a number of Makita Tools as shown below.
Retaining rings are used in various parts of tools.
They are usually installed on a shaft to keep a bearing or a gear from moving.
They are also used in other applications depending on what tool you are working on.
This is an example of an external retaining ring.
• This cord guard is a genuine Makita replacement part and is sold individually.
• Cord guards, also called cord protectors, are designed to slide onto your cord and fit securely at the end, where it’s firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.
• This cord guard will fit cords for the tools listed under the “Compatible Tools” listing. It is not guaranteed to fit any other cords.
This is an authentic manufacturer approved replacement part designed for use with Makita gas trimmers and blowers. It is designed to keep fuel in the tank. This fuel cap is made out of plastic and it is sold individually. Please note the gas cap retainer is sold separately.
This is an OEM approved replacement part. It is specially designed for Makita gas trimmers/edgers. Its purpose is to filter out dust and debris from contaminating the carburetor and engine. Over time this filter will get clogged and worn no longer performing as intended. This filter is made out of foam and it is sold individually.
To replace this filter a screwdriver is needed.
• Remove the cover screw
• Remove the cover
• Replace the filter element
• Reassemble and test the unit
