Medium
30-60 minutes
This is an authentic Milwaukee replacement part that has been sourced from the original manufacturer to be used with cut-off/grinders. The durable handle kit includes both halves and is used to house the motor and switch assemblies. This item is available as an individual replacement part, please see illustrated diagram for associative parts.
Handle Kit 14-34-0900
OEM part for: Milwaukee
Part Number: 14-34-0900
$16.22
In Stock
Order within the next 5 hours and your part ships today! 
Jump To:
Frequently Purchased Together ?
Compatibility
This part will fit the following 2 machines
Milwaukee
2680-20 (SER B96A) Cordless 18 Volt 4-1/2" Cut-Off/Grinder View Diagrams & Manuals
2680-22 (SER B96A) Cordless 18 Volt 4-1/2" Cut-Off/Grinder View Diagrams & Manuals
This item works with the following types of products:
- Grinder Parts
Customer Part Reviews ?
Average Rating (out of 5):
Click to filter by ratings:
5 stars
3
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
Fit just like the original
My grinder has had a hard life. I use it all the time. It had gotten so hot that it melted the case where the bearing for the motor is centered in the case. This fixed it in about 20 min. Just take all the screws out, swap the parts over and put the screws back in. Like new again.
Ian -
September 14, 2022
Verified Purchase
Just what I needed
New part, fit as it should. I use this website to buy all of my replacement parts.
Guest -
February 4, 2020
Verified Purchase
works as expected
arrived quickly
Guest -
October 25, 2019
Verified Purchase
t
t
t -
t days ago
Verified Purchase
eReplacementParts Team
t
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Handle Kit
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
melted case
frank - December 8, 2021
Tool Type
Grinder
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver, Pliers, torx bits
Parts Used
split the case in two, removed parts from both sides, made sure that i didn't break any wires and put it back the same way it came apart, be careful that you don't pinch the wires between the case halves, the one screw that was different was a torx bit that has a hole in it, that was at the bottom of the milwaukee grinder by the battery, that screw had a raised point in the middle, i think they call that a security screw
Did you find this story helpful?
Thanks for voting and helping fellow customers!
the rear bearing on armature overheated due to hard use and caused the plastic bearing housing/handle to melt which cause rubbing on motor internal components
Isaac - January 18, 2021
Tool Type
Grinder
Difficulty
Easy
Time
30-60 minutes
Tools Used
, torx screw drivers: h15 and t20.
Parts Used
removed blades, guard and handle, removed all screws on casing and grinder head (all are t20 except one h15 located on back of handle near battery attachment area) removed wire harness, switches and grinder head. Clean and inspected for wear and other damage. installed internals in new casing as they were installed in old casing, repacked angle gears with fresh grease.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Grinder got hot and was sparking inside.
Donald - December 28, 2020
Tool Type
Grinder
Difficulty
Medium
Time
1-2 hours
Tools Used
, Torx driver
Parts Used
1, Removed gear case and handle ;by removing 9 Torx screws. The 10th screw was a security type Torx which I was forced to saw in half.
2. Removed switches and motor.
3. Soldered new brush card to switch.
4. Reinstalled brush card and switches in new handle. (The heat from the motor bearing had melted the case and allowed the armature to rub against the stator). Bearing inspection did not show anything wrong the bearing.
5. Reassembled with only 9 screws.
6. Enjoyed the pleasure of a successful repair.
2. Removed switches and motor.
3. Soldered new brush card to switch.
4. Reinstalled brush card and switches in new handle. (The heat from the motor bearing had melted the case and allowed the armature to rub against the stator). Bearing inspection did not show anything wrong the bearing.
5. Reassembled with only 9 screws.
6. Enjoyed the pleasure of a successful repair.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
