Easy
15-30 minutes
Filter Assembly E106632
OEM part for: Husky, Industrial Air
Part Number: E106632
$26.73
In Stock
Order within the next 9 hours and your part ships today! 
Jump To:
Frequently Purchased Together ?
Compatibility
This part will fit the following 4 machines
Husky
C303H 30-Gallon Portable Air Compressor View Diagrams & Manuals
C041H 4 Gallon 225 Psi High Performance Crew Electric Portable Air Compressor View Diagrams & Manuals
C331H 33 Gallon Portable Air Compressor View Diagrams & Manuals
Industrial Air
C151I 1.7-Hp 15-Gallon Air Compressor View Diagrams & Manuals
This item works with the following types of products:
Customer Part Reviews ?
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Filter Assembly
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Filter missing
David - June 16, 2021
Tool Type
Compressor
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Adjustable Wrench
Parts Used
Installed part less than 2 minutes. Work great.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
compressor wouldn't start
James - August 21, 2020
Tool Type
Compressor
Difficulty
Easy
Time
15-30 minutes
Tools Used
, torx #20 driver
Parts Used
1. Removed the cover shroud from compressor/motor. (required long torx 20 driver)
2. Removed the old switch from shroud.
3. Snapped in new switch.
4. Unscrewed old filter and screwed in new one.
5. Tested unit.
6. Reattached shroud.
2. Removed the old switch from shroud.
3. Snapped in new switch.
4. Unscrewed old filter and screwed in new one.
5. Tested unit.
6. Reattached shroud.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
took a long time to build pressure
Bruce - July 6, 2020
Tool Type
Compressor
Difficulty
Easy
Time
15-30 minutes
Tools Used
Socket set, Nutdriver
Parts Used
I found it very easy to figure out what was wrong with my compressor as it took over about 45 min. to build pressure in the tank, after looking at the air filter I knew it was clogged so I ordered one with the piston assembly, It took longer to remove the dust covering of the unit than it did to remove and replace the piston unit. Once it was changed out and all back together the compressor ran like new.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
air pressure would never go above 50
MARTY - May 4, 2019
Tool Type
Compressor
Difficulty
Medium
Time
30-60 minutes
Tools Used
Socket set, Wrench Set, Adjustable Wrench, Breaker bar
Parts Used
Removed plastic shroud
removed the conrod bolts ( on both sides required breaker bar to get loose )
reed housing was easy to remove ( take note however which direction the housing is attached ) if you attach it the wrong way, when you start the compressor, you will fill quite a bit of air coming out where there should be none at all.
With the ConRod from Eparts, there were casket rings that were available for replacing in the reed housing.
Using a sturdy piece of metal inserted in the wheel will help remove some of the bolts and allow for the belt drive to be removed for easier install. Once the conrod removed, I observed that there was metal upon metal marks inside the bell housing. This was because there was some breakage in the rubber ring that cause air to leak thru and thus only allow to build up air pressure to go above 50 PSI. With the new conrod in place, it worked great right off the bat.
removed the conrod bolts ( on both sides required breaker bar to get loose )
reed housing was easy to remove ( take note however which direction the housing is attached ) if you attach it the wrong way, when you start the compressor, you will fill quite a bit of air coming out where there should be none at all.
With the ConRod from Eparts, there were casket rings that were available for replacing in the reed housing.
Using a sturdy piece of metal inserted in the wheel will help remove some of the bolts and allow for the belt drive to be removed for easier install. Once the conrod removed, I observed that there was metal upon metal marks inside the bell housing. This was because there was some breakage in the rubber ring that cause air to leak thru and thus only allow to build up air pressure to go above 50 PSI. With the new conrod in place, it worked great right off the bat.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Broken filter.
Mike - May 28, 2018
Tool Type
Compressor
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
, No tools needed.
Parts Used
Screwed on the new filter.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
The manifold on my air compressor was leaking.
Don - April 13, 2018
Tool Type
Compressor
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Wrench Set
Parts Used
Took the handle, shroud, and the hose coming from the motor. Had to use the gauges and the pop off valve from the old manifold. Also replace the filter at the bottom of the motor. It was a very simple repair.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
