Burner G312-2600-W2

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Screwdriver, .

Burnt out

I had to put in two burners and it took me less than 5 minutes to put them in.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

0 of 1 people found this instruction helpful

Tool Type:

Outdoor Grill

Parts Used:

Grease Cup - G430-0033-W1

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Screwdriver

burner corroded

remover old burnes and installed new ones with cross over tube.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

0 of 1 people found this instruction helpful

Tool Type:

Outdoor Grill

Parts Used:

Logo Plate - G305-0008-W1

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers

My bar-b-que grill was showing severe signs of wear and tear

I removed all of the inner parts of the grill and put in new burners, heat tents and crossover
tube as well as purchased a new grate for the grill. The total cost was about $35.00 but a new grill would have been at least $200. I polished the outside with steel wool and spray painted it with heat resistant spray paint. Your schematic of all the parts was invaluable.
G. Smith

Did you find this story helpful?

Thanks for voting and helping fellow customers!

0 of 1 people found this instruction helpful

Tool Type:

Outdoor Grill

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Pliers

Burners worn

Removed the igniter from the burner, removed gas crossover from both burners, installed both burners, installed the ignitor, installed gas crossover. There were no extra screws to re secure the ignitor and the crossover so I had to find other screws to secure. Other than that, all went well.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

0 of 1 people found this instruction helpful

Tool Type:

Outdoor Grill

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Screwdriver, Adjustable Wrench, Wire brush

Corrosion of parts

1. Removed old parts using Phillips screwdriver and 5/16 wrench.
2. Took advantage of emptied grill tub to thoroughly clean it out.
3. Installed new burner tubes & carryover tube with supplied screws, reusing the screws & nuts from the far end of the grill's burner tubes,(5/16 wrench used here and cleaning them first).
4. Placed the new heat tents over burners.
Done!

Did you find this story helpful?

Thanks for voting and helping fellow customers!

0 of 1 people found this instruction helpful

Tool Type:

Outdoor Grill

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Screwdriver, Pliers, drill

The screws were to hard to get out most off them were rusted

Remove all old parts, clean inside, replace with new parts. No instructions needed.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

0 of 1 people found this instruction helpful

Tool Type:

Outdoor Grill

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver

Burners and carry tube rusted out,

Parts fit perfectly and was a good price, although they took a while to be shipped. Very happy with the purchase.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

0 of 2 people found this instruction helpful

Tool Type:

Outdoor Grill

Parts Used: