This genuine OEM sourced replacement ball bearing is a standard item which has multiple uses on a variety of power tools. Please check diagrams for proper application of this item. The bearing is specially designed to reduce friction between rotating parts. Over time it will wear out, at this point it should be replaced. This is a sealed metal bearing and it is sold individually.
Removed the brushes from both sides of housing. Separated the housing from the gear housing buy removing 4 screws. Removed the armature from the housing. Used hammer and punch to drive off the bearing from end of armature shaft. Carefully set the new bearing on the shaft and tapped it on with the hammer. Installed the armature and housing
... Read more in reverse.
Read less
Did you find this story helpful?
Thank you for voting!
Bearings needed replacement
John from DISCOVERY BAY, California
1 personfound this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable), Wrench set
1. Removed drive roller housing and covers.
2. Pulled drive gear off of drive shaft.
3. Removed c clips.
4. Replaced bearings.
5. Reinstalled clips, and drive gear.
6. Reinstalled housing and covers.
7. Tested good.
Did you find this story helpful?
Thank you for voting!
The rear bearing seized and spun in the plastic housing causing excessive play. At first glance I thought the brushes had failed due to large sparks coming from the rear of the housing. Further invest
I removed all the screws from the drill body using an extended length torx bit. I believe it was a number 5. Pulled off the gear box, then pulled out the armature that had the bearing pressed on. To remove the bearing required a little creativity. I just slid a pair of needle nose pliers under the bearing and used a vice to support the ar
... Read moremature. I then used a pinch and hammer to tap the armature shaft out of bearing. I then carefully tapped on the new bearing. The entire trigger assembly needed to be disconnected to allow removal of the field from the old housing. That essentially allowed the field to slide out but when installing the field into the new housing, I had to carefully tap in the field assembly to seat it correctly. Care needs to be taken when removing one of the black wires into the trigger assembly. There is a hole that one of the black wires inserts into it which has an internal clamping mechanism. A very small screwdriver was used to insert into a hole adjacent to the wire that will release the internal clamp. IGÇÖd recommend that photos be taken before removing wires so you will know where the wires reconnect to the trigger assembly and brushes. I assembled in reverse order and the drill works as good as new. What most likely saved me from further damage is I stopped operating the drill upon first seeing it malfunction but not before the drill body housing became melted and the bearing seat became out of round thus allowing the armature to flop around inside the field. In all I think it cost me around $30 to fix.
Replaced the brushes by removing screws that hold the brushes in. Then I removed the old brushes and installed the new ones. Replaced the screws.
Removing the bearing took some time to decide the best way. I ended up using my press after making a jig to fit around the bearing, was no problem at all..........Thanks for the
... Read more fast service on the parts...
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP12123518
Manufacturer Part Number: 681761001
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
