This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 18 Gauge • 10 Feet Long
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Dewalt belt sander replaced power cord
Power cord exact fit. Your process and eliminate procedure is great. My favorite is your exploded views
Guest - April 29, 2019
Verified Purchase
★★★★★
★★★★★
It took me less than 20 minutes to replace the cord ( i did have the crimp style wire nuts on hand) on
Almost the same cord , restraint was the same. love the length of the replacement cord.
Guest - May 4, 2020
Verified Purchase
★★★★★
★★★★★
Right on the money
Part was identical to the original and went on easy but didn’t come with blade connectors
Guest - May 19, 2020
Verified Purchase
★★★★★
★★★★★
great service
great service
Robert - September 8, 2020
Verified Purchase
★★★★★
★★★★★
Great service
Part was received and was exactly what I needed to repair my dewalt random orbital sander. Excellent service. I am a regular customer.
Rodney - June 28, 2023
Verified Purchase
★★★★★
★★★★★
Good cord bad information
The picture when you purchase is different than the second picture here I asked specifically are the connectors on the ends of the cord and was told yes, they were not. So after waiting for a week and a half for a 40$ cord that I had. I called again and spoke to a more knowable man and paid $2.50 each and extra shipping - i don’t care so much about the cost it is the time and messing around. It has been a week and a half waiting for two end power clips that they and I paid for for 5 days
Super place to get parts great selection and this is the only time for bad info, but shipping seems to be by pony express most orders come in a day or two and free but a week or two and expensive - ok the products are super so I will keep shopping
Guest - July 24, 2020
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Removed the old wire, cut the new leads to length and crimped on the new terminals. Replace the wire inside the sander per the original. Not complicated, just need to do correctly to ensure the top cover fit.
Removed top of orbital sander. Unplugged old cord. Soldiered new blades onto new cord. Plugged in new cord in sander. Replaced the top. Plugged in to test
This used Dewalt planer DW677 was a \"gift\" from a friend. The cord was easily replaced after removing 1/2 of the cover. The carbide blades were removed using the spanner which is just a small narrow wrench. Turn the retaining nuts clockwise to enable the two blade holders to be slid out of the planer. Pull out the old carbide blades and
... Read more insert the new. Slide both units into the drum and back off the retaining nuts to tighten in place. Take care to index each carbide cutter on the drum so they are in the same location on the drum. This was the most difficult step but overall a piece of cake.
Removed the screws from the switch cover
Removed the screw holding the switch
Removed the old cord from the switch
Cut the cord wires to the correct length and installed the terminals
Installed the cord to the switch
Mounted the switch to the handle
Installed the switch cover
Did you find this story helpful?
Thank you for voting!
Cord wore out and shorted due to strain reliever being worn out and broken.
1. Removed the tool case.
2. Cut the wires to remove the crimp connectors.
3. Stripped the ends of the new cord.
4. Threaded on the strain reliever.
5. Crimped/taped connectors.
6. Reassembled.
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10169874
Manufacturer Part Number: 330072-97
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
