Washer

Repair Difficulty:

Medium

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Socket set, Wrench Set

Left side of mower deck would not raise or lower. Found adjusting nut and bolt were missing.

1. Installed new adjusting nut.
2. Measured the height of deck on right side.
3. Used wrench to adjust the left side to equal the right side.
4. Tighten everything down, job completed.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

2 of 2 people found this instruction helpful

Tool Type:

Lawn Mower

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

30-60 minutes

Tools Used:

Pliers, Socket set, Tape Measure

Left side deck adjustment gear fell off

1. Removed the temporary fix.
2. Lowered deck onto wooden shims on the left side set to the same height as the right side.
3. Removed the pin in the linkage to make it easier to line up deck and parts.
4. Installed parts, tightened into place, replace linkage pin.
5. Checked deck height at lowest, idle and highest levels to ensure it was correct.
6. Cleaned up tools and tested mower.

This was easily done in the driveway with basic tools. I would recommend checking all nuts and bolts when you do your spring maintenance and oil changes throughout the year.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Pliers, Socket set

The deck belt was secured by a regular bolt by previous owner. The deck dropped off and the belt broke.

1. I disassembled the deck
2. Added the adjustable deck screw
3. Changed the belt
4. Reassembled the deck.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Screw, 7/16-20, 2.75, Gr5 - 710-3180

Tab-Handle - 984-5599

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Socket set, None

Bracket in bolt and washer on the handle was missing

Ordered new bolt washer and bracket and used socket set to install them

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Tractor

Parts Used:

TT-Tap Scr. 5/16-18 x .75\\\\ - 710-1238

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Socket set

Deck adjustment screw came and could not be located.

Set height of deck to be even by putting a board across bottom.
Aligned deck adjustment screw holes
Screwed in Deck Adjustment Gear, washer, and screw

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used:

Hex Nut 5/16-18 - 912-3010

Shoulder Spacer, .625 X .324 - 948-0331

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Socket set, Wrench Set

Lawnmower deck bolt fell out

Ordered lost parts & reattached deck arm

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Tractor

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

30-60 minutes

Tools Used:

Pliers, Socket set

The mower deck would not adjust to an even level. The part that levels the deck had fallen off and could not be found.

1. I dropped the mower deck from the tractor.
2. Installed the new deck adjustment gear.
3. Reattached the deck to the tractor and cut the grass evenly.
It took about 1 hour. It was a snap with the new correct parts. The parts came within 4 days. Thanks ereplacementparts for your support and superior service.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used: