Shop All Uni Parts
We sell only genuine Uni ® parts.
Enter Your Model Number
Shop Uni Parts & Product Types
Same Day Shipping
Toll Free Support
Repair Help & Videos
Most Popular Uni Replacement Parts
Uni Oven Heating Element
10 Reviews
In Stock
Part Number: 316075103
$40.64
The Oven Bake Element is a black, metal part which supplies heat to the oven. This element is 19-1/2" wide x 18-1/2" long and has 3-1/2" inserts. It is rated as "Easy" to install by users, and attaches to the bottom of the oven. If you notice visible damage, or that your oven is not receiving heat properly then it may be a problem with this part. Check your model number and user manual to see if this is the right part for you. It is important for you to disconnect your appliance from the power source before performing this repair. After disconnecting your appliance, remove the two screws/nuts connecting the old element, pull it out, and discard if faulty. Simply connect the new element prongs where the old element fit, and screw it back in.
Uni Belt,dryer,lc
In Stock
Part Number: 137292700
$17.21
This is an original Frigidaire, Gibson, Kenmore, Tappan, Kelvinator, Westinghouse, Crosley, Electrolux part for use with Dryers. The drum belt attaches to the motor pulley and spins the drum as the motor rotates. This part is sold individually. This belt is 89 1/2 X 1/4 inches. Because it is made of rubber it is common for this part to become brittle and need to be replaced. Here is a list of tools that are needed to replace the drum belt a Phillips screwdriver, putty knife and a Flat Blade Screw Driver.
Uni Infinite Switch Large Element
5 Reviews
In Stock
Part Number: 316436001
$30.89
This infinite burner switch, also commonly known as a surface element control switch is a genuine OEM replacement part used in electric ranges/cooktops. It is 240V and designed for an 8-inch surface element. The switch controls the heating of the surface element and turns it on/off as needed. If you have noticed that your range is not heating at all, or it is overheating, and you have difficulties switching off the appliance, then you will likely need to replace the burner switch. Disconnect the range from the power source to before beginning the repair. Pull off the control knob and detach the back panel to access the switch. Disconnect the wire connectors from the old switch and remove the screws that hold it in place. It is recommended to take a picture of how the wires are routed for the installation. Place the new burner switch in the mounting position and reconnect the wires to the new switch. Secure it with the appropriate fasteners and reattach the back panel. Place the control knob back on and reconnect the range to the power source.
Uni Evap Motor Service Kit
1 Review
In Stock
Part Number: 5303918549
$76.34
This evaporator fan motor kit includes the fan motor, its clips, and its terminal connectors. Located in the back panel of the freezer compartment, it circulates air over the evaporator coils to ensure even distribution of cold air. It needs replacement if you notice unusual noises coming from the freezer or the presence of frost or ice buildup on the rear wall of the freezer. To replace the motor, empty the freezer and clear any shelving. Remove the evaporator cover and disconnect the harness connecter in the top left corner. Once the cover is detached, disconnect the harness from the old motor. Proceed to remove the ice maker connector and the fan cover, making sure to release any necessary harnesses. Detach the fan blade and remove the front mounting bracket. You will need to reuse the spacer washer and the grommet from the bracket. To install the new motor, slide the grommet from the old front bracket onto the new motor before seating the motor into the grommet of the rear bracket. Finally, reassemble all the components in reverse order. Remember to note that this OEM replacement kit does not include any additional hardware.
Uni Wheel & Bushing Assy
In Stock
Part Number: 5304532229
$6.88
This wheel and bushing assembly is specifically made for the lower rack of your dishwasher. It makes it easier for you to slide the rack in and out smoothly. This includes one axle or clip and one wheel or roller. Made of gray plastic, it securely attaches to the sides of the lower rack. You will know it needs replacement if you experience difficulties moving the rack, notice wobbling or instability, or observe physical damage. To replace it, start by fully removing the lower rack and detach the old wheel. Align the new wheel with the bushing and snap it into place. Once you have replaced the rack, ensure it moves freely without any issues. Remember, the wheel and bushing assembly is sold individually, so confirm the quantity required for your appliance. This replacement part has been updated and if the wheel in the picture does not match your old one, it is recommended that you replace all the wheels in your dishwasher.