Genuine Manufacturer Approved replacement Burner Tube designed for certain Char-Broil Grills. This part is made out of Stainless Steel and it is Sold Individually. These tubes are made out of stainless steel. They allow grill temperature to be properly maintained. Easy to install with included hardware.
Troubleshooting
This part works with the following brands:
Char-Broil
This part works with the following products:
Grill
★
Customer Part Reviews
?
4.4
Average Rating (out of 5):
★★★★★
★★★★★
(5 Reviews)
Click to filter by ratings:
5 stars
4
4 stars
0
3 stars
0
2 stars
1
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Simple Repair
Grill is working like a champ.
Guest - July 3, 2019
Verified Purchase
★★★★★
★★★★★
Perfect fit
Grill working great again
Doyle - November 12, 2019
Verified Purchase
★★★★★
★★★★★
Great Service
Very easy process and found all the parts i needed. Now my grill is up and running like new.
Guest - June 18, 2021
Verified Purchase
★★★★★
★★★★★
Char-Broil Burner Tube
I had looked around for quite a while for these burner tubes. They arrived in about three or four days. The tubes are a direct replacement for my gas grill. I may order more as my grill has a few tears on it and parts are hard to come by but I found them here.
Guest - September 6, 2021
Verified Purchase
★★★★★
★★★★★
Product seems right but
Product seems right but the grill is not working correctly since the new parts were installed. I emailed the company about my issues and instead of replying they sent me a review their product and service link.
Guest - May 20, 2019
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Drilled out burner tube screws. Removed threaded section with vice grips. Removed and discarded burner tubes, carryover tubes and heat tents. Cleaned grill with paint scraper. Installed new parts. Pretty easy but grimy work.
Removed grill grates and flame covers
Unscrewed fasteners holding flame tubes and cross over tubes
Lifted flame tubes out of the grill and removed
Placed new flame tubes one by one in the grill
Found one of the new flame tubes was too long no found the part # was not correct.
Found 1 good tube from one of t
... Read morehe old ones removed
Placed the old tube with the new ones in the grill
Used the new fasteners to secure the new flame and cross over tubes
Placed the new flame covers over the flame tubes
Placed the grill grates back in place
Read less
Did you find this story helpful?
Thank you for voting!
The carryover tubes were burned out, had holes in them.
The parts were great and I\'m very happy with the finished product. The job would have been easy if the old screws hadn\'t been so corroded.
I used the book that came with the grill to figure out how it was all put together. The difficult part was getting the old nuts and screws off. My husband had to drill out one of them
... Read more. The grill is at least 2 maybe 3 years old so it was pretty bad. I plan to replace worn parts more often in the future so the job won\'t be so difficult.
1. Removed grill grates and burner tents
2. Attemped to loosen screws on burner tubes and ignitor plugs
3. Loosened crossover tube screws
4. Removed rusted parts
5. Inserted new burner tubes and attached with new screws
6. Attached new crossover tubes with new screws
7. Inserted and screwed in new ignit
... Read moreor plugs
8. Replaced tents and grates
I removed tube burners first. Had to drill out corroded screws. Not too hard to do. Carry over tubes came out easily. Replaced tube burner. They fit perfectly. Then simply installed carry over tubes. With perfect fit they screwed in very easily. My Charbroil grill is, and works like brand new.
Did you find this story helpful?
Thank you for voting!
Cross over tubes were rusted out and then I broke the burners trying to get the crossover tubes out
1. Gutted the old burners and crossover tubes.
2. Installed new burners.
3. Installed new crossover tubes.
4. Test fired ignition probe.
5. Secured everything.
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10295865
Manufacturer Part Number: G560-6400-W1
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
