This is a genuine OEM replacement part. Sold individually.
This kit was made to replace the old switch on the Miter Saws that was discontinued. It includes both handle halves, handle to carry saw, new switch, screws and wire terminals. It also includes an installation sheet.
Flat head screwdriver is needed for repair.
This switch is a common replacement part and is compatible with the Miter Saw models listed below.
Troubleshooting
This part fixes the following symptoms:
Won't turn on
This part works with the following brands:
DeWALT
Black and Decker
This part works with the following products:
Miter Saw
★
Customer Part Reviews
?
4.7
Average Rating (out of 5):
★★★★★
★★★★★
(26 Reviews)
Click to filter by ratings:
5 stars
19
4 stars
6
3 stars
0
2 stars
1
1 star
0
< Prev
1
2
3
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
20 minute fix
Watching the video made it very simple. Well done. Saved me from having to buy a new mitre saw.
Guest - July 17, 2019
Verified Purchase
★★★★★
★★★★★
Good Quality replacement parts - fixed my saw.
If you have a saw like this to begin with, you're probably a DIY person. The on-line video is a must as the included information sheet is more of a schematic than directions. Not difficult to remove and replace, but I did have to "massage" the plastic to accept my existing strain relief boot. 3 of the 4 wires are different colors, so easy to follow what goes where as the arrangement differs from the original switch. Only need to examine the 2 black wires for proper placement (study the included information sheet here). Took me about 45 minutes including the plastic surgery with my rotary tool.
Guest - July 29, 2019
Verified Purchase
★★★★★
★★★★★
Kit was well made
All parts included and went together easily. Instructions a little hard to read but they worked. Saw runs great!
Guest - November 13, 2019
Verified Purchase
★★★★★
★★★★★
Switch repair kit.
My product arrived quickly was in perfect condition, fit perfectly, made my repair fast and easy. Replacement parts is where I always go for my replacement parts.
Guest - May 4, 2020
Verified Purchase
★★★★★
★★★★★
replacement part exactly as needed
Even with the delays for shipping due to virus, the part arrived quickly and was exactly as pictured and exactly what I needed to finish my repair
Guest - May 15, 2020
Verified Purchase
★★★★★
★★★★★
Worked great
received when told. Gold star
Guest - August 18, 2020
Verified Purchase
★★★★★
★★★★★
Easy repair
All good, easy process, highly recommend you for parts. Tks
Guest - January 4, 2021
Verified Purchase
★★★★★
★★★★★
Easy
Worked as expected. All parts were there, arrived quickly, was a cinch to put together
Guest - April 9, 2021
Verified Purchase
★★★★★
★★★★★
Got just fine
It fit and works great
Jerry - June 11, 2021
Verified Purchase
★★★★★
★★★★★
this was exactly what I needed-easy instructions included.
Great company-if I need additional parts this is my go to site. Thank you.
Guest - June 17, 2021
Verified Purchase
< Prev
1
2
3
Next >
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
Be the first to ask our experts a question about this part!
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
The kit included most things necessary to replace the switch. Wire strippers are needed to crimp on the new ends of the wiring. Instructions were included, but hard to understand. But they are helpful. Anyone with any tool repair experience should be able to figure it out no problem though.
Did you find this story helpful?
Thank you for voting!
Blade brake stopped working; eventually the saw wouldn\'t start at all.
This switch kit contains a revised switch along with a new style handle assembly that is needed to retrofit the switch to older saws. Replacement is simply a matter of removing the old handle and switch assembly and reinstalling the new parts in the reverse order. The positions of the wires on the new switch are exactly the same as the ol
... Read mored one. Once the new switch is in place, route the wires to it through the provided channels and cut the old ring terminals off right at the switch. This will leave the wires the proper length for you to strip about 1/4\" of insulation and crimp on the provided spade connectors. Push these onto the switch, check the wire placement to be sure nothing is going to get pinched, and you\'re ready to reinstall the handle top. Note that the new switch, unlike the old one, is only held to the handle bottom by one screw. The second hole if for the screw that comes down through the handle top half.
The instructions enclosed with replacement switch were printed so light they were not readable. Called and \"Richard\" directed me to a You-tube video produced by your company which talked me through the repair in minutes. The only other problem centered around the replacement handle. The original screws are too long for this handle, so I
... Read more put spacers on each screw prior to attaching.
Read less
Did you find this story helpful?
Thank you for voting!
The original switch would start but not shut off, dangerous situation.
Disassembled per the instructions, had to remove the original power cord restraint as it would not fit in the new assemble of the handle. Wire diagram was good but very faded print, difficult to read. The unit now performs like new. Thanks for being there for us, I had the part in two days, the manufacturers service center did not have it
... Read more in stock and told me a week to ten.
Only real problem was the instruction sheet was unreadable due to printing quality.
Look VERY close at the wiring connections on the switch. It is NOT a straight point to point connection. Two of the wires must be switched side to side.
Save the screws, some must be reused with the new handle.
Bought new switch and handle set. Arrived within three days. Watched instructional video - very helpful!
Removed old handle and switch set and installed new handle without issues. The saw feels even more powerful than before. Maybe getting more current to the motor now?
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
