eReplacementParts.com
877-346-4814
Makita Parts
Preferred Partners of
Repair Parts Home  Power Tool Parts  Makita Parts  664265-4 Power Cord

Power Cord

Part Number: 664265-4
Makita
Availability: 25+ in stock
Price: $20.23
Order within the next 11 hours
and your part ships today!

*This part replaces obsolete part #: 664234-5.

Product Information
Manufacturer: Makita
Product Number: 664265-4
Classification: Part
Weight: 0.57 lbs.
Also Known As: AC Cord, Power Supply Cord, Cord Set, Electric Cord
Shipping: Ships Worldwide
Specifications
  • Genuine Makita replacement power tool cord
  • 2 Wire
  • Tough 16 gauge wiring
  • 8 feet in length
  • Sturdy plug and insulation
Length: 8'
Gauge: 16
Wires: 2
Type: Bare Wire
Description:
This is a genuine Makita replacement power tool cord. It is constructed with thick insulation for long service life and a strong two-prong plug. The connection end of the cord comes pre stripped for easy installation. The cord is eight feet long with sturdy 16 gauge wires.

This cord will fit the Makita tools listed below. It can work for other applications and for other tools as well, but compatibility is not guaranteed.
Frequently Purchased With
Compatibility

This part is compatible with the following machines:

Makita
Expand the 111 compatible machines
Products Compatibility

This item works with the following types of products:

  • • Circular Saw
  • • Drill
  • • Grinder
  • • Impact Wrench
  • • Miter Saw
  • • Reciprocating Saw
  • • Saw
  • • Shear
Expand List
Questions & Answers

No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
19 of 19 people found this instruction helpful
Tool Type:
Circular Saw
Parts Used:
Power Cord - 664265-4
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, stuff to put ends on wire
Someone had cut plug wire near saw end
1. Removed 4 or 5 Philips screws from handle (nuts stayed in removed handle piece)
2. Removed 2 screws holding tension on cords end the one holding switch to saw
3. Un-screwed wire from switch (black wire white wire) remember which wire goes where
(white wire was on side of switch with part #s or something
BACK TOGETHER
1. Attach new cord to switch remembering wirers have to be in the same place as removed
2. Replace restraining clip and 2 screws and tuck all wires in to saw
3. Replace handle part watch that nuts stayed in place
4. Inspect job should look just like it did but with shinny new cord
PLUG IT IN, PULL TRIGGER (remember it IS a SAW and be careful )
Did you find this story helpful?
Thanks for voting and helping fellow customers!
5 of 5 people found this instruction helpful
Tool Type:
Miter Saw
Parts Used:
Cord Guard - 682505-8
Power Cord - 664265-4
Compression Spring 9 - 231297-2
Switch Lever - 414157-5
Switch SP115F-1 - 651895-0
Repair Difficulty:
Medium
Time Spent Repairing:
More than 2 hours
Tools Used:
Screwdriver, Wrench Set, wire stripper and cutter
Power cord was frayed and needed replacement
1. Removed 4 phillips head screws to remove handle assembly from saw.
2. Removed 5 phillips head screws to open handle assembly and provide access to wiring
3. Removed power cord and its connection to a connector component and the switch.
4. Cut new wires as needed to make connections
5. Noted that the new strain relief was not the correct size. Discovered that this was due to the labeling on the miter saw which indicated that it was a model LS 1030 when it was actually a model LS 1030N. Was able to determine this from drawings which were accurate.
6. Used old strain reliever which was in good condition
7. Then disaster: One of the handle assembly screws fell into the armature casing. The armature unit could not be removed as it appeared to be stuck in the casing. This condition has been reported by others. After a couple of days trying magnets, shaking the casing, using wires, etc. I finally was able to see where the screw was stuck with a flashlight shining on the casing air vents. Once seeing the screw I was then able to remove it.
8. Then took a little time to discover how a retention spring functioned together with the safety release button on the unit.
9. Voila! Repair complete and the saw started and has been resurrected from the dead!!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 3 people found this instruction helpful
Tool Type:
Grinder
Parts Used:
Cord Guard - 682505-8
Power Cord - 664265-4
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Wire Crimping tool
Needed a new cord
Remove the screws from the housing
Remove the cord clamp
Remove the cord wires from the switch
Put strain relief on the new cord
Connect the wire the switch
Install the cord clamp
Put the housing back together
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 3 people found this instruction helpful
Tool Type:
Circular Saw
Parts Used:
Power Cord - 664265-4
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers, Power Drill
cord worn out after 30 years
Remove the handle cover to expose the cord, remove the two screws from the cord hold. Remove the cord leads from switch. It is easier if you remove the switch too. Slide off the cord relief and place it on the new cord. The cord does not include terminals for the switch. Attach cord to switch, replace switch and cord hold with the two screws. Attach handle half
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Circular Saw
Parts Used:
Power Cord - 664265-4
Outer Flange - 224275-9
Inner Flange 40 - 224268-6
Hex. Flange Head Bolt M8X20 - 265315-4
Carbon Brush Set - CB154
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, wire crimpers
Repaired power cord, brushes and replaced flange nuts
Removed half of the switch handle, Remove two screws from cord holder, removed the the cord wires from the switch, cut the cord leads to the correct length, had to locate two terminals to put on the end of the cord leads. Attached cord leads to switch.don't for get to put the old cord relief back onto the new cord. reattached the cord holder with the two screws. Then replace the handle half. For the brush set, I removed the brush caps, then removed the old brush set and installed the new set and the brush caps. I also replaced the inner and outer flanges, and the blade bolt.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Circular Saw
Parts Used:
Power Cord - 664265-4
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver
Brother in law sawed through my power cord.
1. Started figuring it out.
2. Removed a couple more screws than necessary, removed the cover piece of shell.
3. Took a good look at how the damaged cord was attached.
4. Detached it.
5. Fed in the new cord, using the attaching rings from the old cord (wish the new cord came with those rings already attached.
6. Put the pieces back together.
7. Actually, I had to do two saws - one circular and one reciprocating, so I repeated this process. Despite them both being Makita, the routing and attachment process was different. A very pleasant couple of hours one evening.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Circular Saw
Parts Used:
Cord Guard - 682505-8
Power Cord - 664265-4
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Needed new cord
Take off the handle, take off the cord holder, take off the cord wires to the switch.
Slide the new strain relieve onto the new cord. Cut the cord wires to the correct length. connect the cord wires to the switch. Screw the cord holder on. Screw the handle on.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Impact Wrench
Parts Used:
Power Cord - 664265-4
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Power cord worn out
Remove on half of the switch handle
Remove the cord clamp
Disconnect the cord wires
Remove the cord relief from the old cord to the new cord
Connect the cord wires
Attach the cord clamp
Replace the handle half
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Circular Saw
Parts Used:
Cord Guard - 682505-8
Power Cord - 664265-4
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Wire stripper and connectors.
Wire old, cracked and exposed.
Separated handle and trigger section. This required removal of 5 screws. This exposed the wire connections. Removed old wire. It had a wire connector, sleeve type from a previous repair. This had to be reconnected. Threaded the wire thru the rubber wire protector. Made all connections, reassembled and tested. I put this off for ages. I had tried to fix it with electrical tape. Doing it right is always best!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Circular Saw
Parts Used:
Switch - 651172-0
Power Cord - 664265-4
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers, Nutdriver
Saw would not start
I already had removed my old parts while waiting for my new parts to arrive. There are 2 screws on the switch and 2 for the cord. Both parts were installed within 15 minutes. My favorite saw is new again.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
4.9
Average Rating (out of 5):
36 Reviews
Click to filter by ratings:
5 stars
33
4 stars
2
3 stars
1
2 stars
0
1 stars
0
  • Highest Rating
  • Most Recent
< PREV
  • 1
  • 2
  • 3
NEXT >
  • thanks
    all parts arrived at once - four power tools have new life!
    Guest - July 28, 2022 Verified Purchase
    Right part
    This is a very old Makita saw that I love. I was glad to find original cord to fix it
    Guest - April 16, 2022 Verified Purchase
    Better Than I Expected
    I had to use a circular saw to finish a kitchen remodel and the saw was probably 30 years old or better as well as the worn out and taped up cord. Told my wife the saw was going to the shop for a new power cord as soon as I was done. Instead I went on-line and found the perfect replacement cord and fixed the saw myself at home. I figure saved at least $50-60. Now, I wish I would have replaced the cord first.
    Guest - February 19, 2022 Verified Purchase
    Perfect part
    No issues with part when received
    Guest - February 15, 2022 Verified Purchase
    Worked very well
    The cord came quickly, installed easily and was a great replacement for the original frayed cord.
    Guest - February 12, 2022 Verified Purchase
    Great part and easy fix.
    Cord is a factory item and works like the original. Makita does a great job.
    Guest - January 12, 2022 Verified Purchase
    Just what I was looking for!
    I have been holding on to this circular saw that had belonged to my dad the motor was fine, but the power cord was shot to hell. Finally was able to get the replacement cord I needed and its working great!
    Guest - December 4, 2021 Verified Purchase
    Angle grinder parts
    Parts were shipped in a timely manner. Parts were exact match to what was being replaced.
    Guest - November 18, 2021 Verified Purchase
    Easy Repair, New life to my favorite circular saw.
    Arrived quickly, worked great!
    Guest - October 31, 2021 Verified Purchase
    The Makita 5007NB circular saw replacement power cord.
    The replacement power cord was new and fit perfectly. With the help of u tube videos on the web, the replacement was easy and quick to do. The packaging was secure and the part arrived in a reasonable amount of time. Bill
    Guest - September 15, 2021 Verified Purchase
    Verified Purchase
    eReplacementParts Team
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    • 2
    • 3
    NEXT >
    Product Information
    Manufacturer: Makita
    Product Number: 664265-4
    Classification: Part
    Weight: 0.57 lbs.
    Also Known As: AC Cord, Power Supply Cord, Cord Set, Electric Cord
    Shipping: Ships Worldwide
    Repair Guides
    Watch the Repair Video for Power Cord
    Articles:
    This article contains tips and basic steps for replacing power cords for most types of power tools, machines, and other ...
    September 18, 2009
    Step-by-step instructions for removing and installing the power cord on your Makita angle drill....
    February 27, 2018

    Fixing things makes sense...

    ...And we make it easy! With our Fix app, you always have a personalized repair guide on-hand. Easily find manuals and replacement parts on your phone while you’re DIYing in the garage or garden.

    "Love the flexibility of the app to add everything in the home and garage. Access to manuals and parts right there makes it convenient."

    Available on the App Store Get it on Google Play
    eReplacementParts.com
    7036 South High Tech Dr.
    Midvale, UT 84047
    visa mastercard discover american express PayPal