OEM Bissell Carpet Cleaner Parts & Accessories

Geared Brush Belt (left Side) – Part Number: B-203-6688

$9.82

Manufacturer Part Number:: B-203-6688

This is a Genuine Bissell geared Motor belt, it is sold individually. When replacing Left Belt it is recommended to replace the Right Belt part #B-203-6804 as well for best operation. The belts on vacuum should be checked periodically. If belts are worn or stretched they need to be replaced to avoid potential damage to the unit.

Duct Gasket

$5.17

Minimum Quantity of 2 required

Manufacturer Part Number:: B-010-4050

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Bissell carpet cleaners. The purpose of this gasket is to provide a tight seal for the duct. It provides an identical replacement for a missing or a faulty hardware that was installed on a new unit. Make sure to refer to the appropriate diagrams of your model for the correct location and applicatio...

Valve Solenoid

$42.60

Manufacturer Part Number:: B-203-7436

Cap And Insert Assy

★★★★★

(6)

$6.99

Manufacturer Part Number:: B-203-5014

This is an original Bissell part. This part is used on many models of Bissell carpet cleaners. The Cap And Insert Assembly is used on the Clean Tank Assembly. The Cap allows for easy flow of clean water and cleaning solution. This part should be replaced if it leaks or becomes damaged in other ways. This part requires no tools to replace.

Left & Right Elevator Lever

★★★★★

(1)

$9.67

Manufacturer Part Number:: B-200-0010

These are the right and left elevator levers for a variety of vacuum models. These levers are responsible for adjusting the height of the vacuum and its brush to suit different floor types, levels, and cleaning requirements. Crafted from high-quality OEM plastic, this pair of levers is sold individually and includes two levers and necessary springs. As these levers are made of plastic, they can br...

15 Brush Assembly

★★★★★

(2)

$37.53

Manufacturer Part Number:: B-203-1283

This is a genuine OEM approved replacement part designed for use with Bissell vacuum cleaners. It spins to pick up the dust and dirt from the carpet. This part is made out of plastic and it is sold individually. When replacing this part you will need a screwdriver. • Remove access plate and take off the belt • Remove old brush roller and snap the new one into place • Connect belt to the sp...

Right Side Geared Belt

★★★★★

(3)

$7.85

Manufacturer Part Number:: B-203-6804

Genuine Bissell supplied replacement part for a variety of Carpet Cleaners. This item is sold individually. When replacing Right Belt it is recommended to replace the Left Belt as well for best operation. The belts should be checked periodically. If belts are worn or stretched they need to be replaced to provide best performance.

Autoload Gasket

$5.17

Minimum Quantity of 2 required

Manufacturer Part Number:: B-203-6679

The autoload gasket is made out of rubber and attaches to the tank. This part is available as an individual replacement. This authentic item is supplied directly from the original equipment manufacturer for use with carpet cleaners by Bissell. No tools should be needed during the replacement of this part. It may become broken and will need to be replaced.

Tank Filter

$5.17

Manufacturer Part Number:: B-203-0105

It is an authentic manufacturer-sourced replacement part which is specially designed for use with Bissell Carpet Cleaners. This filter is specifically designed to collect any lint that is sucked up with the cleaner and prevents it from entering the solution tank. It is recommended that this is cleaned out after every use. This is made of a plastic material and is sold separately.

Pump Belt

★★★★★

(6)

$15.25

Manufacturer Part Number:: B-010-0620

Genuine Bissell replacement part,this item is sold individually. This belt is driven by the motor to operate the Pump Assembly for the models listed below. Overtime the Belt will wear and stretch, causing the pump to not work properly. It is advised to get an extra belt to keep on hand.

Pivot Arm Retainer Assembly

★★★★★

(3)

$4.13

Manufacturer Part Number:: B-555-9113

This authentic OEM retainer assembly secures the left and right pivot arms of the brush roll assembly on your steam vacuum. The pivot arms allow the brushes to move and adjust to various surfaces for effective cleaning, and the retainer assembly ensures they stay in place during operation. The assembly comes with the necessary hardware for replacement and is typically located on the sides of the f...