OEM Carpet Cleaner Parts Replacement Parts & Accessories

Motor Belt

$11.14

Manufacturer Part Number:: E02445

The motor belt is made out of rubber. It is a genuine item that is supplied by the original equipment manufacturer for use with EDIC lawn tractors. This part is available individually. During the installation process, a screwdriver might be needed to replace this part. It will require replacing if it becomes broken or stretched.

Spring, Brush

$5.95

Minimum Quantity of 2 required

Manufacturer Part Number:: D10426

This is an authentic replacement part manufactured for use with Edic vacuums. The brush spring is commonly used to provide tension on the slide block assembly. This brush spring is available as an individual replacement part, please see model diagram for associative parts.

Tank Filter

$5.95

Manufacturer Part Number:: B-203-0105

It is an authentic manufacturer-sourced replacement part which is specially designed for use with Bissell Carpet Cleaners. This filter is specifically designed to collect any lint that is sucked up with the cleaner and prevents it from entering the solution tank. It is recommended that this is cleaned out after every use. This is made of a plastic material and is sold separately.

Switch

$23.60

Manufacturer Part Number:: B00188

Geared Brushroll Belt

$5.95

Manufacturer Part Number:: BR-1075

This is a genuine Bissell part used with carpet cleaners. This belt fits onto the motor drive shaft and around the brushroll. This geared belt has notches that are designed to fit into sprockets on the brushroll, providing efficient transfer of motion. These parts are made to be replaced every one to two years. This belt is sold individually.

Geared Brush Belt (left Side)

★★★★★

(6)

$9.82

Manufacturer Part Number:: B-203-6688

This is a Genuine Bissell geared Motor belt, it is sold individually. When replacing Left Belt it is recommended to replace the Right Belt part #B-203-6804 as well for best operation. The belts on vacuum should be checked periodically. If belts are worn or stretched they need to be replaced to avoid potential damage to the unit.

Cap And Insert Assy

★★★★★

(6)

$7.70

Manufacturer Part Number:: B-203-5014

This is an original Bissell part. This part is used on many models of Bissell carpet cleaners. The Cap And Insert Assembly is used on the Clean Tank Assembly. The Cap allows for easy flow of clean water and cleaning solution. This part should be replaced if it leaks or becomes damaged in other ways. This part requires no tools to replace.

Pump Belt

★★★★★

(6)

$15.25

Manufacturer Part Number:: B-010-0620

Genuine Bissell replacement part,this item is sold individually. This belt is driven by the motor to operate the Pump Assembly for the models listed below. Overtime the Belt will wear and stretch, causing the pump to not work properly. It is advised to get an extra belt to keep on hand.

Autoload Gasket

$5.95

Minimum Quantity of 2 required

Manufacturer Part Number:: B-203-6679

The autoload gasket is made out of rubber and attaches to the tank. This part is available as an individual replacement. This authentic item is supplied directly from the original equipment manufacturer for use with carpet cleaners by Bissell. No tools should be needed during the replacement of this part. It may become broken and will need to be replaced.

Pivot Arm Retainer Assembly

★★★★★

(3)

$5.95

Manufacturer Part Number:: B-555-9113

This authentic OEM retainer assembly secures the left and right pivot arms of the brush roll assembly on your steam vacuum. The pivot arms allow the brushes to move and adjust to various surfaces for effective cleaning, and the retainer assembly ensures they stay in place during operation. The assembly comes with the necessary hardware for replacement and is typically located on the sides of the f...

Right Side Geared Belt

★★★★★

(3)

$7.85

Manufacturer Part Number:: B-203-6804

Genuine Bissell supplied replacement part for a variety of Carpet Cleaners. This item is sold individually. When replacing Right Belt it is recommended to replace the Left Belt as well for best operation. The belts should be checked periodically. If belts are worn or stretched they need to be replaced to provide best performance.