Part Location Diagram of 530071750 Husqvarna Gasket Set
See part B-7 in the diagram
( Grid squares measure 1x1 inch )

Gasket Set 530071750

Manufactured by:
Husqvarna
ERP Number:
ERP12602552
Part Number:
530071750
Original Equipment Manufacturer ?
  Works with your model  P3500!
Special Order

A Bit Difficult 

30 - 60 mins 

(11 rated repairs) ?
  Works with your model   P3500!

Product Description

?

This is a Manufacturer Approved replacement kit used on a variety of Gas Trimmers/Pruners. This gasket set includes the major gaskets to replace when rebuilding the engine. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time gaskets tend to deteriorate and will need to be replaced. Gaskets in this kit are made out of Composite Material and O-Rings are made out of Rubber.

Frequently Purchased Together

?

Troubleshooting

This part works with the following brands:
  • Weed Eater
  • Poulan
  • Husqvarna
  • Craftsman
This part works with the following products:
  • Trimmer
  • Pole Saw
Part# 530071750 replaces these:
530071750,

Customer Part Reviews

?
4.2
Average Rating (out of 5):
★★★★★
★★★★★
(6 Reviews)
Click to filter by ratings:
  • 5 stars
    4
  • 4 stars
    1
  • 3 stars
    0
  • 2 stars
    0
  • 1 star
    1
  • 1
Sort by:  
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.

Questions & Answers

?

Our customer Service team is at the ready daily to answer your part and product questions.

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Ask our Team

We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

Does this fit my product?

Customer Repair Instructions

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

A Bit Difficult 

30 - 60 mins 

(11 rated repairs) ?
  • 1
  • 2
Sort by:  
Sorry, we couldn't find any existing installation instruction that matched.

Would not run with choke in off position.

Joseph from Halls, Tennessee

11 of 11 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
These are the steps i used... Remove fuel lines from carburetor note position of each. Open up cover of air box. Remove air filter. Remove two screws with Allen wrench. Remove air box. Slighty remove carburetor and unhook throttle cable linkage noting the way it hooks up. Remove carburetor. Make sure old gasket doesn\'t stick to carburet or adapter. Remove two screws and remove carburetor adapter. Take carburetor adapter, air box, and air box cover and clean with toothbrush and dishwash liquid. Dry thoroughly. Take a q-tip dip in cleaner and clean around cylinder where adapter fits. Push screws through carburetor adapter and put new gasket on screws pushing it on adapter so it lines up perfectly. Tighten adapter on cylinder. Push screws through air box, new carburetor, and place new gasket on screws against carburetor so gasket lines up perfectly. Install throttle linkage cable to carburetor. Tighten screws back down. Clean air filter, or replace then install air box cover. Hook fuel lines back up in proper position. Always, ALWAYS use non-ethanol gas in your weed eater with proper oil mixture. My Poulan weed eater is 13 years old and this is the first time I habe replaced anything on it.
Did you find this story helpful?
Thank you for voting!

Would not start

FRED from LOMPOC, California

10 of 10 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
530057781, 581263701, 530071750
I followed the instructions that were included with the gasket kit. I\'m glade that they were included. I then removed the fuel lines from the carburetor. Remember where they went. Then removed the two screw holding the fuel tank. Then installed the new fuel tank and replaced the fuel lines. Then removed the air filter cover and replaced the air filter and put the cover back on.
Did you find this story helpful?
Thank you for voting!

Hard starting, lack of power, adjusting carburetor made no difference.

Dean from Stockton, California

6 of 6 people found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers
1. Removed shrouds
2. Removed engine from trimmer mount
3. Removed cylinder from block
4. Removed retaining rings from piston, pushed piston pin out, removed piston.
5. Reversed above procedure installing new piston
6. Installed piston ring, oiled piston and ring, then slid cylinder over piston
7. Bolt cylinder down
8. Remove accessories from first cylinder and install on new cylinder
9. Reinstall engine on trimmer mount, reinstall shrouds
10. Start engine and adjust carburetor
Did you find this story helpful?
Thank you for voting!

Weed eater trimmer will not start.

John from Stockton, California

5 of 5 people found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set
1. Replaced the carburetor assembly.
2. Replaced air filter foam.
3. Replaced spark plug.
4. Replaced fuel tank cap.
5. Waiting for the fuel line hoses and fuel filter. (found hoses deteriated)
Did you find this story helpful?
Thank you for voting!

Carburetor wouldnÆt prime

Mark from Victor, West Virginia

2 of 2 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Parts Used:
530071811, 530071750
Removed the two gas lines from the carburetor removed the two screws holding it in place under the air cleaner unhook the throttle cable.
Used new gasket and carburetor from ereplacementparts in reverse order. It was simple primed the carburetor pulled the starter three times back in business
Did you find this story helpful?
Thank you for voting!

Needed new carburator

Kevin from Mill Valley, California

2 of 2 people found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
1. Removed old carb
2. Put on new gasket on new carb
3. Installed new air filter insert
4. Installed new fuel pick up
Did you find this story helpful?
Thank you for voting!

Replaced carb and gasket.

Stephen from SUMMERFIELD, Florida

1 person found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
530071822, 530071750
Pretty straight forward if you have the proper tools and a mechanical aptitude. Removed fuel lines, air filter and 2 hex bolts that held the defective carb. Replaced with new parts and put back together. Filled the tank with fresh gas
Did you find this story helpful?
Thank you for voting!

Bad carb and cracked carb adapter

Kris from Traverse city , Michigan

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
530071811, 530057547, 530071750
Removed air filter assembly
Removed carb bolts
Replaced carb adapter o-ring
Reinstalled in reverse order
Did you find this story helpful?
Thank you for voting!

Line trimmer would not start

Janice from NORTH RICHLAND HILLS, Texas

1 person found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench set
Parts Used:
530071822, 530071750
Removed to air filter.
Removed the carburetor
Installed the new carburetor.
Did you find this story helpful?
Thank you for voting!

Gasjet was in bad shape

Antonio from HUNTERSVILLE, North Carolina

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
530016429, 530071750
Put the new gasket on and threaded the new screws in because the old ones were bad.
Did you find this story helpful?
Thank you for voting!
  • 1
  • 2

Model Cross Reference

This part works with the following models:
ERP Number: ERP12602552
Manufacturer Part Number: 530071750
Brand Model Number Description
Poulan 325 Edger - 325 - Poulan Pro Gas Trimmer - Pro Trimmers And Edgers
Craftsman 358.791032 Trimmer - 2-Cycle Gasoline Weedwacker
Craftsman 358791010 Trimmer - Weedwacker
Craftsman 358791030 Trimmer - Trimmer
Craftsman 358791031 Trimmer - Trimmer
Craftsman 358791032 Trimmer - Trimmer
Craftsman 358791050 Trimmer - Trimmer
Craftsman 358791051 Trimmer - Trimmer
Craftsman 358791370 Trimmer - Trimmer
Craftsman 358791520 Trimmer - Trimmer
Craftsman 358791530 Trimmer - Trimmer
Craftsman 358791540 Trimmer - Trimmer
Craftsman 358791560 Trimmer - Trimmer
Craftsman 358791590 Trimmer - Trimmer
Craftsman 358791620 Trimmer - Trimmer
Craftsman 358791820 Trimmer - Trimmer
Craftsman 358796600 Trimmer - Trimmer
Husqvarna 475 Trimmer - Te Handheld Trimmer
Husqvarna 475Y Trimmer - Te Handheld Trimmer
Craftsman 944514360 Trimmer - Trimmer
Craftsman 944514361 Trimmer - Trimmer
Craftsman 944514460 Trimmer - Trimmer
Craftsman 944514550 Trimmer - Trimmer
Craftsman 944515460 Trimmer - Trimmer
Craftsman 944515560 Trimmer - Trimmer
Craftsman 944516360 Trimmer - Trimmer
Craftsman 944516550 Trimmer - Trimmer
Craftsman 944516560 Trimmer - Trimmer
Craftsman 944516561 Trimmer - Trimmer
Weed Eater 952711767 Trimmer - Weed Eater String Trimmer Model 952711767 Parts