This is an authentic Shindaiwa replacement part that has been sourced from the original manufacturer to be used with trimmers and brushcutters. The throttle cable is used to link the carburetor and the throttle trigger to actuate the valve to adjust the engine's output. This item is available as an individual replacement part.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
throttle was just like the one on the t27 weed eater that i been using for 18 years easy to replace 30 mins at the most
just what i needed works great great company to buy from
Guest - September 7, 2020
Verified Purchase
★★★★★
★★★★★
Shindawa throttle cable
Went to several mower shops around me looking for throttle cable for shindawa weedeater. Couldn’t find model number or serial number for its almost 30 years old. Only place I could see the possible replacement was here. Took 15 minutes to install and adjust. Back in business
Guest - July 11, 2022
Verified Purchase
★★★★★
★★★★★
Perfect Fit
The cable arrived quickly and fit perfectly in my trimmer.
Guest - July 28, 2022
Verified Purchase
★★★★★
★★★★★
Weedeater cable
It fit my weedeater perfectly,an it arrived promptly.
Guest - October 15, 2022
Verified Purchase
★★★★★
★★★★★
Great website - easy to navigate - good communication
parts were exactly what I required - Many Thanks
Iglobal - February 24, 2023
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Loosen two screws on throttle lever assy, loosen two screws on power head-to-trimmer tube clamp. Twist and slide power head off tube. Coated new grip inside with silicone spray and slide onto tube. Slide power head onto shaft and engage drive shaft, retighten clamp screws. Install new cable and spring. NOTE: found it best to route new cab
... Read morele and kill wires thru new grip channel before sliding new grip onto shaft! Also clean and lube anything that needs attention during tear-down always makes reassembly much easier.
Replaced old throttle cable with new one and also replaced the switch. Used the old wires for the switch as they were still good and already in place. Throttle replacement, at the throttle is easy. However, the carb end is a \"pain in the butt\". As opposed to the usual hook up, it uses a spring and pin attached with the carb end of the
... Read morecable. I had to \"rig it\" to work correctly and not sure how long the system will hold up. Works great for the present but we will see what the future brings. Shindaiwa should have made the carb end with a lever (like most other machines) and not design it with this \"Rube Goldberg\" setup! Parts, however, were perfect and delivery time (considering the holidays) was not bad!!
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP9242529
Manufacturer Part Number: V430003400
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
