Genuine Dewalt replacement part, this item is sold individually. The purpose of the N074647 Foot is to keep the Miter Saw Stands shown below, stable and keep them from sliding on the surface they are placed on. There are four of these feet on each stand. To fasten the foot to the stand you will need to order part number 330019-32 Screw.
Troubleshooting
This part works with the following brands:
DeWALT
This part works with the following products:
Tool Stand & Cart
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(4 Reviews)
Click to filter by ratings:
5 stars
4
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Chop saw stand feet
It was a pleasant shopping experience, easy to use’ good representation of the product & was received as expected. Thank you ereplacementparts.
Guest - June 21, 2019
Verified Purchase
★★★★★
★★★★★
Just what I needed and wanted but couldn't find anywhere else
I think these will probably be better than the original that came with the stand. They are a lot firmer than the the soft rubber foot pads that came with it and should hold up better they installed easy and fit perfectly. Shopping with you guys was a snap and shipping was reasonable. Thank you
Robert - July 18, 2020
Verified Purchase
★★★★★
★★★★★
Percect!
Odd part never expected to obtain. Replacement part had an exact match. Great service works great on time delivery and fairly priced. The American way for Americans
Guest - November 13, 2020
Verified Purchase
★★★★★
★★★★★
Saw stand feet
Better than the originals! Fit tight and don’t fall off.
Guest - October 14, 2025
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1. Remove the slide off rubber feet, if any stayed on.
2. Measure where you need to drill holes for the new style of feet. (Measure from center hole to the low place on the outside of the foot. Then add 1/32GÇ¥ so the foot will be tight on the leg.)
3. Find the centerline on the leg and mark a cross on the centerline and your
... Read moremeasured distance.
4. Use a punch or drill bit that will not walk on the aluminum. Use a drill bit that is just bigger than the screw threads. The threads are meant to grab the plastic feet and spin free on the aluminum legs.
5.Slide on new feet. You will see the new feet are angled. Place the taller side to the outside.
6. Install new screw by hand. (No power tools) Threads are in plastic. Be gentle!
Read less
Did you find this story helpful?
Thank you for voting!
The rubber feet on my DeWalt mitre saw stand had worn thru the metal legs and would scratch a finished surface floor.
1. Removed original rubber feet.
2. Placed new foot on the bottom of the mitre saw stand leg.
3. Measure for retaining screw(which was not on original foot).
4. Mark/drill hole for retaining screw.
5. Install screw to secure the new foot to the leg of the stand.
6. Repeat procedure on 3 remaining legs.
Did you find this story helpful?
Thank you for voting!
Many parts were damaged or missing due to over 10 years of professional use.
Replaced the power cord and the work light. Replaced the pin that holds the saw in the closed position. Also replaced a few other misc parts. The light, power cord and pin were the biggest reasons I needed to repair just due to safety and ease of use. The pin was the hardest part to replace because I had to remove the large pivot pin
... Read morethat the entire saw hinges on by tapping it out with a mallet and a 1/2\" socket extension. The spring that holds the saw in the up position comes out when the hinge pin is removed making it extremely difficult to put everything back together. I realized after the fact that there are holes just below the spring that you can insert a screw driver or Allen wrench or similar object which holds the spring in the closed position. I still haven\'t figured out if there is an easier way to replace the spring itself since you obviously can\'t hold it in the closed position if you are trying to replace it, but my spring is fine and I don\'t have to worry about that now. There were no websites or videos that I could find to show how this is done, but I figured it out. Would have been easier if there was something that explained the holes for holding the spring before I took it all apart and the spring ejected the saw arm.
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_1.gif "Part Location Diagram of N074647 DeWALT Foot")
_WW_1.gif "Part Location Diagram of N074647 DeWALT Foot")
